Washing machine error codes and fault guides
Browse 229 published, evidence-gated Washing machine guides. Each page states the supported model and region, official source, safe checks, and the point to stop.
Washing machine fault guides
145–168 of 229
an unbalanced load condition
F0E9 is identified by Maytag's official support as an unbalanced load condition. Follow the model-scoped checks and safety boundary below.
a washer control error
F1E1 is identified by Maytag's official support as a washer control error. Follow the model-scoped checks and safety boundary below.
the lid lock cannot engage because the lock area may be obstructed
F5E2 is identified by Maytag's official support as the lid lock cannot engage because the lock area may be obstructed. Follow the model-scoped checks and safety boundary below.
a door or lid lock condition is preventing the cycle from starting
F5E3 is identified by Maytag's official support as a door or lid lock condition is preventing the cycle from starting. Follow the model-scoped checks and safety boundary below.
the lid is open or the control cannot confirm a closed lid
F5E4 is identified by Maytag's official support as the lid is open or the control cannot confirm a closed lid. Follow the model-scoped checks and safety boundary below.
a motor-speed sensing error
F7E1 is identified by Maytag's official support as a motor-speed sensing error. Follow the model-scoped checks and safety boundary below.
low water flow or a washer fill alert
F8E1 is identified by Maytag's official support as low water flow or a washer fill alert. Follow the model-scoped checks and safety boundary below.
a problem with the detergent dispenser system on select models
F8E2 is identified by Maytag's official support as a problem with the detergent dispenser system on select models. Follow the model-scoped checks and safety boundary below.
drain times are longer than expected
F9E1 is identified by Maytag's official support as drain times are longer than expected. Follow the model-scoped checks and safety boundary below.
a long-fill condition caused by slow filling or siphoning
LF is identified by Maytag's official support as a long-fill condition caused by slow filling or siphoning. Follow the model-scoped checks and safety boundary below.
a long-drain problem in the drain-pump system
Ld is identified by Maytag's official support as a long-drain problem in the drain-pump system. Follow the model-scoped checks and safety boundary below.
the detergent cartridge is not detected on select models
dET is identified by Maytag's official support as the detergent cartridge is not detected on select models. Follow the model-scoped checks and safety boundary below.
water-injection problem
E10 is identified by Midea support as water-injection problem. Follow the official, model-scoped checks and service boundary below.
water overflow
E12 is identified by Midea support as water overflow. Follow the official, model-scoped checks and service boundary below.
water overflow detected
E12 is identified by Midea support as water overflow detected. Follow the official, model-scoped checks and service boundary below.
washer does not drain
E21 is identified by Midea support as washer does not drain. Follow the official, model-scoped checks and service boundary below.
water level does not change within the published drain interval
E21 is identified by Midea support as water level does not change within the published drain interval. Follow the official, model-scoped checks and service boundary below.
door-open condition
E30 is identified by Midea support as door-open condition. Follow the official, model-scoped checks and service boundary below.
door cannot be locked after repeated attempts
E30 is identified by Midea support as door cannot be locked after repeated attempts. Follow the official, model-scoped checks and service boundary below.
water-level sensor signal outside the normal range during the wash cycle
E33 is identified by Midea support as water-level sensor signal outside the normal range during the wash cycle. Follow the official, model-scoped checks and service boundary below.
motor-inverter PCB detects abnormal signals
E50 is identified by Midea support as motor-inverter PCB detects abnormal signals. Follow the official, model-scoped checks and service boundary below.
motor failed to start five times
E60 is identified by Midea support as motor failed to start five times. Follow the official, model-scoped checks and service boundary below.
motor speed feedback is below the specified range
E61 is identified by Midea support as motor speed feedback is below the specified range. Follow the official, model-scoped checks and service boundary below.
actual motor speed is substantially above the target speed
E62 is identified by Midea support as actual motor speed is substantially above the target speed. Follow the official, model-scoped checks and service boundary below.