AEG · Refrigerator · Fault guide

AEG Refrigerator E01 error

ErrorE01

E01 is identified by AEG support as temperature-sensor warning. Follow the official, model-scoped checks and service boundary below.

Quick answer

What E01 means

AEG Refrigerator E01: temperature-sensor warning. This interpretation applies to AEG refrigerators and fridge freezers covered by the linked UK support article in United Kingdom / English.

Model scope
AEG refrigerators and fridge freezers covered by the linked UK support article
Region
United Kingdom / English
Verified
✓

Primary evidence: AEG fridge-freezer E01/E02/E03/E06/E07 support.

Open official source ↗
✓
What the code means

temperature-sensor warning

Isolate the appliance when safe. record the exact code and contact an authorised service centre for a sensor diagnosis Do not open fixed panels or test live circuits.

Typical symptoms

01E01 is shown on the AEG refrigerator display, indicator, or connected app
02The published condition is: temperature-sensor warning
03The control cannot confirm the documented measured condition or sensor reference represented by E01
04The important observation is when E01 appears and whether the exact published action changes that condition

Fault area and what the code does not prove

Separate the manufacturer-defined condition from components that still need exact-model diagnosis.

01Manufacturer-defined fault area — temperature-sensor warning
02E01 identifies a measured-condition or sensor path, not a completed proof that the sensor itself failed
03Model boundary — apply this interpretation only to AEG refrigerators and fridge freezers covered by the linked UK support article

Safe next steps

  1. 1
    Confirm the exact AEG Refrigerator E01 model and displayed code before taking action.
  2. 2
    Keep the appliance in a safe state and use only the external checks named in the official source.
  3. 3
    If the condition remains, stop and arrange qualified service; do not open panels or bypass a safety device.

Step-by-step diagnosis

  1. 1
    Photograph the complete E01 display before changing controls or removing power
  2. 2
    Confirm that the full model number is covered by this scope: AEG refrigerators and fridge freezers covered by the linked UK support article
  3. 3
    Confirm that the observed condition matches the published meaning: temperature-sensor warning
  4. 4
    Published check — record the exact code and contact an authorised service centre for a sensor diagnosis
  5. 5
    Stop at the published service boundary after these actions
  6. 6
    do not add a restart or test cycle that AEG does not specify for E01
  7. 7
    Published check — Give service the E01 photo, full model and serial number, when it appeared, and the result of every published external check
  8. 8
    Stop at the published service boundary after these actions; do not add a restart or test cycle that AEG does not specify for E01

Service-safe actions

  1. 1
    record the exact code and contact an authorised service centre for a sensor diagnosis
  2. 2
    Give service the E01 photo, full model and serial number, when it appeared, and the result of every published external check

Repair planning

€Cost for the first check
E01 cost planning: The source-listed external check costs €0. A qualified sensor-system diagnosis is generally planned within €110–€250 before any model-specific part is approved.
⏱Time for the first check
E01 time plan: 10–20 minutes for the documented E01 external check; allow 30–90 minutes for measured sensor, wiring, and control diagnosis.
🔧Tools
Photo of the complete E01 display, Full model and serial number, The exact-model manual for the published external check, No live sensor-circuit test equipment
▣Parts or consumables
E01 parts decision: E01 describes temperature-sensor warning; it does not prove the sensor itself has failed. A blocked path, connector, wiring, control input, or the measured condition can produce the same reported area.

What not to do

  • Do not bridge, heat, cool, wet, or electrically probe a sensor to clear E01
  • Do not replace a sensor until its circuit and the condition it measures have been checked
  • Do not run an extra test cycle after the source tells you to stop or arrange service for E01

Preventive maintenance

  • 1
    Follow the exact AEG maintenance schedule for the refrigerator and keep the model, serial number, and service history available
  • 2
    If E01 begins recurring despite the documented maintenance, stop repeating the same action and request exact-model diagnosis

Frequently asked questions

What exactly does E01 identify?

AEG identifies it as temperature-sensor warning.

Which action is actually supported for E01?

record the exact code and contact an authorised service centre for a sensor diagnosis; Give service the E01 photo, full model and serial number, when it appeared, and the result of every published external check.

Can I run another test after E01?

Not unless the official procedure above explicitly includes it. Complete the safe external actions, then keep the appliance stopped at the service boundary.

Does E01 prove which part failed?

No. It identifies “temperature-sensor warning”; parts are selected only after the exact model and failed function are confirmed.

What information should accompany a service request?

The E01 photo, full model and serial number, the operating stage when it appeared, and the result of each published check.

Related faults

Compare related codes for the same appliance or manufacturer before replacing parts.