Bosch · Dishwasher · Fault guide

Bosch Dishwasher E0105 error

ErrorE0105

E0105 is identified by Bosch support as faulty heater electronics detected during self-test. Follow the official, model-scoped checks and service boundary below.

Quick answer

What E0105 means

Bosch Dishwasher E0105: faulty heater electronics detected during self-test. This interpretation applies to Bosch dishwasher models covered by the linked Bosch US error-code support page in United States / English.

Model scope
Bosch dishwasher models covered by the linked Bosch US error-code support page
Region
United States / English
Verified
✓

Primary evidence: Bosch US official dishwasher error-code support.

Open official source ↗
✓
What the code means

faulty heater electronics detected during self-test

Isolate the appliance when safe. Do not open the control or heater circuit; contact Bosch Customer Support for the exact model. Do not open fixed panels or test live circuits.

Typical symptoms

01E0105 appears on the dishwasher display
02The faulty heater electronics detected during self-test condition may stop, pause, or limit the appliance
03The same code returns when the model-specific condition remains active

Likely causes

Start with the least invasive explanation and stop if the check requires internal electrical or sealed-system access.

01faulty heater electronics detected during self-test
02The exact model manual must be used before any internal diagnosis

Safe next steps

  1. 1
    Confirm the exact Bosch Dishwasher E0105 model and displayed code before taking action.
  2. 2
    Keep the appliance in a safe state and use only the external checks named in the official source.
  3. 3
    If the condition remains, stop and arrange qualified service; do not open panels or bypass a safety device.

Step-by-step diagnosis

  1. 1
    Photograph the complete E0105 display before changing controls or removing power
  2. 2
    Confirm that the full model number is covered by this scope: Bosch dishwasher models covered by the linked Bosch US error-code support page
  3. 3
    Confirm that the observed condition matches the published meaning: faulty heater electronics detected during self-test
  4. 4
    Published check — Do not open the control or heater circuit
  5. 5
    Published check — contact Bosch Customer Support for the exact model
  6. 6
    Stop at the published service boundary after these actions
  7. 7
    do not add a restart or test cycle that Bosch does not specify for E0105
  8. 8
    Published check — Give service the E0105 photo, full model and serial number, when it appeared, and the result of every published external check
  9. 9
    Stop at the published service boundary after these actions; do not add a restart or test cycle that Bosch does not specify for E0105

Service-safe actions

  1. 1
    Do not open the control or heater circuit
  2. 2
    contact Bosch Customer Support for the exact model
  3. 3
    Give service the E0105 photo, full model and serial number, when it appeared, and the result of every published external check

Repair planning

€Cost for the first check
E0105 cost planning: The published isolation or cooldown check costs €0. A qualified heating-system diagnosis is generally planned within €90–€220 before parts; request separate heater, sensor, wiring, labor, and call-out lines.
⏱Time for the first check
E0105 time plan: 5–15 minutes for the E0105 safety check, plus any documented cooldown; a qualified heating-system diagnosis commonly takes 30–90 minutes before repair.
🔧Tools
Phone photo of E0105, Full model and serial number, Timer for the one permitted cooldown or test interval, No live heater-circuit test equipment
▣Parts or consumables
E0105 parts decision: E0105 points to faulty heater electronics detected during self-test, but it does not prove whether the heater, relay, sensor, wiring, circulation system, or control is responsible. Order only the exact-model part confirmed by diagnosis.

What not to do

  • Do not repeat heating cycles, bypass thermal protection, test a live heater or relay, or order a heater from E0105 alone
  • Do not run an extra test cycle after the source tells you to stop or arrange service for E0105

Preventive maintenance

  • 1
    Follow the exact Bosch maintenance schedule for the dishwasher and keep the model, serial number, and service history available
  • 2
    If E0105 begins recurring despite the documented maintenance, stop repeating the same action and request exact-model diagnosis

Frequently asked questions

What exactly does E0105 identify?

Bosch identifies it as faulty heater electronics detected during self-test.

Which action is actually supported for E0105?

Do not open the control or heater circuit; contact Bosch Customer Support for the exact model; Give service the E0105 photo, full model and serial number, when it appeared, and the result of every published external check.

Can I run another test after E0105?

Not unless the official procedure above explicitly includes it. Complete the safe external actions, then keep the appliance stopped at the service boundary.

Does E0105 prove which part failed?

No. It identifies “faulty heater electronics detected during self-test”; parts are selected only after the exact model and failed function are confirmed.

What information should accompany a service request?

The E0105 photo, full model and serial number, the operating stage when it appeared, and the result of each published check.

Related faults

Compare related codes for the same appliance or manufacturer before replacing parts.