Electrolux Dishwasher i43 error

Errori43

i43 is identified by Electrolux support as a pressure-sensor problem. Follow the official, model-scoped checks and service boundary below.

✓

Reference source listed as Electrolux UK dishwasher error-code support.

Open official source ↗

✓

What the code means

a pressure-sensor problem

Isolate the appliance when safe. isolate the dishwasher, record the code and model, and arrange authorised service Do not open fixed panels or test live circuits.

Typical symptoms

01i43 is shown on the Electrolux dishwasher display, indicator, or connected app

02The published condition is: a pressure-sensor problem

03The control cannot confirm the documented measured condition or sensor reference represented by i43

04The important observation is when i43 appears and whether the exact published action changes that condition

Fault area and what the code does not prove

Separate the manufacturer-defined condition from components that still need exact-model diagnosis.

01Manufacturer-defined fault area — a pressure-sensor problem

02i43 identifies a measured-condition or sensor path, not a completed proof that the sensor itself failed

03Model boundary — apply this interpretation only to Electrolux UK dishwasher models covered by the linked support article

Safe next steps

1
Confirm the exact Electrolux Dishwasher i43 model and displayed code before taking action.
2
Keep the appliance in a safe state and use only the external checks named in the official source.
3
If the condition remains, stop and arrange qualified service; do not open panels or bypass a safety device.

Step-by-step diagnosis

1
Photograph the complete i43 display before changing controls or removing power
2
Confirm that the full model number is covered by this scope: Electrolux UK dishwasher models covered by the linked support article
3
Confirm that the observed condition matches the published meaning: a pressure-sensor problem
4
Published check — isolate the dishwasher, record the code and model, and arrange authorised service
5
Stop at the published service boundary after these actions
6
do not add a restart or test cycle that Electrolux does not specify for i43
7
Published check — Give service the i43 photo, full model and serial number, when it appeared, and the result of every published external check
8
Stop at the published service boundary after these actions; do not add a restart or test cycle that Electrolux does not specify for i43

Service-safe actions

1
isolate the dishwasher, record the code and model, and arrange authorised service
2
Give service the i43 photo, full model and serial number, when it appeared, and the result of every published external check

Repair planning

€Cost for the first check
i43 cost planning: The source-listed external check costs €0. A qualified sensor-system diagnosis is generally planned within €90–€220 before any model-specific part is approved.

⏱Time for the first check
i43 time plan: 10–20 minutes for the documented i43 external check; allow 30–90 minutes for measured sensor, wiring, and control diagnosis.

🔧Tools
Photo of the complete i43 display, Full model and serial number, The exact-model manual for the published external check, No live sensor-circuit test equipment

▣Parts or consumables
i43 parts decision: i43 describes a pressure-sensor problem; it does not prove the sensor itself has failed. A blocked path, connector, wiring, control input, or the measured condition can produce the same reported area.

What not to do

Do not bridge, heat, cool, wet, or electrically probe a sensor to clear i43
Do not replace a sensor until its circuit and the condition it measures have been checked
Do not run an extra test cycle after the source tells you to stop or arrange service for i43

Preventive maintenance

1
Follow the exact Electrolux maintenance schedule for the dishwasher and keep the model, serial number, and service history available
2
If i43 begins recurring despite the documented maintenance, stop repeating the same action and request exact-model diagnosis

Frequently asked questions

What exactly does i43 identify?

Electrolux identifies it as a pressure-sensor problem.

Which action is actually supported for i43?

isolate the dishwasher, record the code and model, and arrange authorised service; Give service the i43 photo, full model and serial number, when it appeared, and the result of every published external check.

Can I run another test after i43?

Not unless the official procedure above explicitly includes it. Complete the safe external actions, then keep the appliance stopped at the service boundary.

Does i43 prove which part failed?

No. It identifies “a pressure-sensor problem”; parts are selected only after the exact model and failed function are confirmed.

What information should accompany a service request?

The i43 photo, full model and serial number, the operating stage when it appeared, and the result of each published check.

Real repair outcomes

Did this guide fix your appliance?

Your anonymous response helps us show which repairs work in the real world. One current response is kept per guide.

Loading real repair outcomes…