Haier · Air conditioner · Fault guide

Haier Air conditioner F27 error

ErrorF27

F27 is identified by Haier support as compressor current-sampling circuit fault. Follow the official, model-scoped checks and service boundary below.

Quick answer

What F27 means

Haier Air conditioner F27: compressor current-sampling circuit fault. This interpretation applies to Haier air-conditioner models covered by the linked Malaysia support article in Malaysia / English.

Model scope
Haier air-conditioner models covered by the linked Malaysia support article
Region
Malaysia / English
Verified
✓

Primary evidence: Haier Malaysia air-conditioner error-code support.

Open official source ↗
!
Stop and make safe

compressor current-sampling circuit fault

Isolate the appliance when safe. Switch the unit off and arrange Haier service; do not open the electrical or refrigerant system. Do not open fixed panels or test live circuits.

Typical symptoms

01F27 is shown on the Haier air conditioner display, indicator, or connected app
02The published condition is: compressor current-sampling circuit fault
03The appliance has reached the manufacturer-defined stop or service condition associated with F27
04The important observation is when F27 appears and whether the exact published action changes that condition

Fault area and what the code does not prove

Separate the manufacturer-defined condition from components that still need exact-model diagnosis.

01Manufacturer-defined fault area — compressor current-sampling circuit fault
02F27 defines a service boundary; the failed internal part still requires exact-model diagnosis
03Model boundary — apply this interpretation only to Haier air-conditioner models covered by the linked Malaysia support article

Safe next steps

  1. 1
    Confirm the exact Haier Air conditioner F27 model and displayed code before taking action.
  2. 2
    Keep the appliance in a safe state and use only the external checks named in the official source.
  3. 3
    If the condition remains, stop and arrange qualified service; do not open panels or bypass a safety device.

Step-by-step diagnosis

  1. 1
    Photograph the complete F27 display before changing controls or removing power
  2. 2
    Confirm that the full model number is covered by this scope: Haier air-conditioner models covered by the linked Malaysia support article
  3. 3
    Confirm that the observed condition matches the published meaning: compressor current-sampling circuit fault
  4. 4
    Published check — Switch the unit off and arrange Haier service
  5. 5
    Published check — do not open the electrical or refrigerant system
  6. 6
    Stop at the published service boundary after these actions
  7. 7
    do not add a restart or test cycle that Haier does not specify for F27
  8. 8
    Published check — Give service the F27 photo, full model and serial number, when it appeared, and the result of every published external check
  9. 9
    Stop at the published service boundary after these actions; do not add a restart or test cycle that Haier does not specify for F27

Service-safe actions

  1. 1
    Switch the unit off and arrange Haier service
  2. 2
    do not open the electrical or refrigerant system
  3. 3
    Give service the F27 photo, full model and serial number, when it appeared, and the result of every published external check

Repair planning

€Cost for the first check
F27 cost planning: The source-listed safety check is usually €0. €140–€320 is a typical Europe planning range for diagnosis before parts; it is not Haier pricing. Ask for separate diagnosis, parts, labor, and call-out lines on the quote.
⏱Time for the first check
F27 time plan: 5–10 minutes to document and isolate safely; 30–90 minutes is a typical diagnostic visit before any model-specific repair.
🔧Tools
Phone camera for the complete F27 display, Full model and serial number, Power or water isolation access as described by the official procedure
▣Parts or consumables
F27 parts decision: No component should be ordered from F27 alone. The documented fault area is “compressor current-sampling circuit fault”; the technician must identify the failed model-specific part and revision.

What not to do

  • Do not open fixed panels, test live circuits, bypass protection, or keep operating the appliance after an urgent stop instruction
  • Do not run an extra test cycle after the source tells you to stop or arrange service for F27

Preventive maintenance

  • 1
    Follow the exact Haier maintenance schedule for the air conditioner and keep the model, serial number, and service history available
  • 2
    If F27 begins recurring despite the documented maintenance, stop repeating the same action and request exact-model diagnosis

Frequently asked questions

What exactly does F27 identify?

Haier identifies it as compressor current-sampling circuit fault.

Which action is actually supported for F27?

Switch the unit off and arrange Haier service; do not open the electrical or refrigerant system; Give service the F27 photo, full model and serial number, when it appeared, and the result of every published external check.

Can I run another test after F27?

Not unless the official procedure above explicitly includes it. Complete the safe external actions, then keep the appliance stopped at the service boundary.

Does F27 prove which part failed?

No. It identifies “compressor current-sampling circuit fault”; parts are selected only after the exact model and failed function are confirmed.

What information should accompany a service request?

The F27 photo, full model and serial number, the operating stage when it appeared, and the result of each published check.

Related faults

Compare related codes for the same appliance or manufacturer before replacing parts.