Maytag Dishwasher F10E5 error
F10E5 is identified by Maytag's official support as a diverter leak, also displayed as FAE5 on some models. Follow the model-scoped checks and safety boundary below.
What F10E5 means
Maytag Dishwasher F10E5: a diverter leak, also displayed as FAE5 on some models. This interpretation applies to Maytag dishwasher models covered by the linked Maytag Product Help article in United States / English.
- Model scope
- Maytag dishwasher models covered by the linked Maytag Product Help article
- Region
- United States / English
- Verified
a diverter leak, also displayed as FAE5 on some models
Follow the exact Maytag model instructions. Check for water under the dishwasher and confirm accessible water connections are secure. Press Cancel twice and try one new cycle; arrange service if F10E5 returns. Do not open fixed panels or test live circuits.
Typical symptoms
Fault area and what the code does not prove
Separate the manufacturer-defined condition from components that still need exact-model diagnosis.
Safe next steps
- 1Confirm the exact Maytag Dishwasher F10E5 model and displayed code before taking action.
- 2Keep the appliance in a safe state and use only the external checks named in the official source.
- 3If the condition remains, stop and arrange qualified service; do not open panels or bypass a safety device.
Step-by-step diagnosis
- 1Photograph the complete F10E5 display before changing controls or removing power
- 2Confirm that the full model number is covered by this scope: Maytag dishwasher models covered by the linked Maytag Product Help article
- 3Confirm that the observed condition matches the published meaning: a diverter leak, also displayed as FAE5 on some models
- 4Published check — Check for water under the dishwasher and confirm accessible water connections are secure
- 5Published check — Press Cancel twice and try one new cycle
- 6Published check — arrange service if F10E5 returns
- 7Stop at the published service boundary after these actions
- 8do not add a restart or test cycle that Maytag does not specify for F10E5
- 9Published check — Give service the F10E5 photo, full model and serial number, when it appeared, and the result of every published external check
- 10Stop at the published service boundary after these actions; do not add a restart or test cycle that Maytag does not specify for F10E5
Service-safe actions
- 1Check for water under the dishwasher and confirm accessible water connections are secure
- 2Press Cancel twice and try one new cycle
- 3arrange service if F10E5 returns
- 4Give service the F10E5 photo, full model and serial number, when it appeared, and the result of every published external check
Repair planning
F10E5 cost planning: €0 for a safe external inspection; typically €15–€80 for a confirmed external hose or seal. Internal leak diagnosis is commonly €90–€220 before parts.
F10E5 time plan: 5–15 minutes to shut off water and inspect externally; allow 30–90 minutes for professional leak tracing.
Dry towels and a shallow tray, Flashlight for external connections, Access to the water shut-off
F10E5 parts decision: No part can be selected until the leak location is found. A visibly damaged external hose or seal must match the full Maytag model and connection type.
What not to do
- Do not run another cycle to reproduce an active leak, tilt the appliance, bypass a float switch, or energize wet electrical areas
- Do not run an extra test cycle after the source tells you to stop or arrange service for F10E5
Preventive maintenance
- 1Keep user-accessible filters, seals, hoses, and drain connections clean and inspect them periodically for damage or seepage
- 2If F10E5 begins recurring despite the documented maintenance, stop repeating the same action and request exact-model diagnosis
Frequently asked questions
What exactly does F10E5 identify?
Maytag identifies it as a diverter leak, also displayed as FAE5 on some models.
Which action is actually supported for F10E5?
Check for water under the dishwasher and confirm accessible water connections are secure; Press Cancel twice and try one new cycle; arrange service if F10E5 returns; Give service the F10E5 photo, full model and serial number, when it appeared, and the result of every published external check.
Can I run another test after F10E5?
Not unless the official procedure above explicitly includes it. Complete the safe external actions, then keep the appliance stopped at the service boundary.
Does F10E5 prove which part failed?
No. It identifies “a diverter leak, also displayed as FAE5 on some models”; parts are selected only after the exact model and failed function are confirmed.
What information should accompany a service request?
The F10E5 photo, full model and serial number, the operating stage when it appeared, and the result of each published check.
Did this guide fix your appliance?
Your anonymous response helps us show which repairs work in the real world. One current response is kept per guide.