Vaillant · Heat pump · Fault guide

Vaillant Heat pump F.514 error

ErrorF.514

F.514 is identified by Vaillant support as compressor inlet-temperature sensor fault. Follow the official, model-scoped checks and service boundary below.

Quick answer

What F.514 means

Vaillant Heat pump F.514: compressor inlet-temperature sensor fault. This interpretation applies to Vaillant heat-pump models covered by the linked official UK heat-pump fault-code page in United Kingdom / English.

Model scope
Vaillant heat-pump models covered by the linked official UK heat-pump fault-code page
Region
United Kingdom / English
Verified
✓

Primary evidence: Vaillant UK official heat-pump fault-code support.

Open official source ↗
✓
What the code means

compressor inlet-temperature sensor fault

Isolate the appliance when safe. Record the code and arrange Vaillant engineer service; do not test the sensor or refrigerant circuit. Do not open fixed panels or test live circuits.

Typical symptoms

01F.514 is shown on the Vaillant heat pump display, indicator, or connected app
02The published condition is: compressor inlet-temperature sensor fault
03The affected fill stage does not receive or confirm the expected water supply while F.514 is active
04The important observation is when F.514 appears and whether the exact published action changes that condition

Fault area and what the code does not prove

Separate the manufacturer-defined condition from components that still need exact-model diagnosis.

01Manufacturer-defined fault area — compressor inlet-temperature sensor fault
02F.514 does not distinguish household supply, hose, accessible screen, inlet hardware, wiring, or control until the listed checks are completed
03Model boundary — apply this interpretation only to Vaillant heat-pump models covered by the linked official UK heat-pump fault-code page

Safe next steps

  1. 1
    Confirm the exact Vaillant Heat pump F.514 model and displayed code before taking action.
  2. 2
    Keep the appliance in a safe state and use only the external checks named in the official source.
  3. 3
    If the condition remains, stop and arrange qualified service; do not open panels or bypass a safety device.

Step-by-step diagnosis

  1. 1
    Photograph the complete F.514 display before changing controls or removing power
  2. 2
    Confirm that the full model number is covered by this scope: Vaillant heat-pump models covered by the linked official UK heat-pump fault-code page
  3. 3
    Confirm that the observed condition matches the published meaning: compressor inlet-temperature sensor fault
  4. 4
    Published check — Record the code and arrange Vaillant engineer service
  5. 5
    Published check — do not test the sensor or refrigerant circuit
  6. 6
    Stop at the published service boundary after these actions
  7. 7
    do not add a restart or test cycle that Vaillant does not specify for F.514
  8. 8
    Published check — Give service the F.514 photo, full model and serial number, when it appeared, and the result of every published external check
  9. 9
    Stop at the published service boundary after these actions; do not add a restart or test cycle that Vaillant does not specify for F.514

Service-safe actions

  1. 1
    Record the code and arrange Vaillant engineer service
  2. 2
    do not test the sensor or refrigerant circuit
  3. 3
    Give service the F.514 photo, full model and serial number, when it appeared, and the result of every published external check

Repair planning

€Cost for the first check
F.514 cost planning: €0 to open valves, straighten hoses, or clean an accessible screen; typically €15–€60 for a confirmed replacement inlet hose. If F.514 returns with normal supply, €140–€320 is a typical Europe planning range for diagnosis before parts; it is not Vaillant pricing.
⏱Time for the first check
F.514 time plan: 10–25 minutes for supply, hose, and accessible-screen checks plus one short fill test.
🔧Tools
Dry towels and a shallow tray, Soft brush for a user-accessible inlet screen only, Hand access to the household water valves
▣Parts or consumables
F.514 parts decision: Usually none for the first check. Replace an inlet hose only if it is visibly damaged and the exact Vaillant model specification confirms the correct hose.

What not to do

  • Close the water valves before disconnecting a hose
  • Do not probe the inlet valve electrically or run repeated fill tests if a connection leaks
  • Do not run an extra test cycle after the source tells you to stop or arrange service for F.514

Preventive maintenance

  • 1
    Keep inlet hoses unkinked, close household valves before hose work, and clean only user-accessible inlet screens at the exact-model interval
  • 2
    If F.514 begins recurring despite the documented maintenance, stop repeating the same action and request exact-model diagnosis

Frequently asked questions

What exactly does F.514 identify?

Vaillant identifies it as compressor inlet-temperature sensor fault.

Which action is actually supported for F.514?

Record the code and arrange Vaillant engineer service; do not test the sensor or refrigerant circuit; Give service the F.514 photo, full model and serial number, when it appeared, and the result of every published external check.

Can I run another test after F.514?

Not unless the official procedure above explicitly includes it. Complete the safe external actions, then keep the appliance stopped at the service boundary.

Does F.514 prove which part failed?

No. It identifies “compressor inlet-temperature sensor fault”; parts are selected only after the exact model and failed function are confirmed.

What information should accompany a service request?

The F.514 photo, full model and serial number, the operating stage when it appeared, and the result of each published check.

Related faults

Compare related codes for the same appliance or manufacturer before replacing parts.