Whirlpool · Washing machine · Fault guide

Whirlpool Washing machine No Water Detected error

ErrorNo Water Detected

No Water Detected is identified by Whirlpool support as the washer has not detected incoming water. Follow the official, model-scoped checks and service boundary below.

Quick answer

What No Water Detected means

Whirlpool Washing machine No Water Detected: the washer has not detected incoming water. This interpretation applies to Whirlpool front-load washer models covered by the linked US Product Help article in United States / English.

Model scope
Whirlpool front-load washer models covered by the linked US Product Help article
Region
United States / English
Verified
✓

Primary evidence: Whirlpool US washer error-code support.

Open official source ↗
✓
What the code means

the washer has not detected incoming water

Follow the exact model manual. Check the supply valves and visible inlet hoses with water off, then request service if the message returns. Do not open fixed panels or test live circuits.

Typical symptoms

01No Water Detected is shown on the Whirlpool washing machine display, indicator, or connected app
02The published condition is: the washer has not detected incoming water
03The affected function behaves as described by the manufacturer while No Water Detected is present
04The important observation is when No Water Detected appears and whether the exact published action changes that condition

Fault area and what the code does not prove

Separate the manufacturer-defined condition from components that still need exact-model diagnosis.

01Manufacturer-defined fault area — the washer has not detected incoming water
02No Water Detected identifies the documented condition, not a confirmed replacement part
03Model boundary — apply this interpretation only to Whirlpool front-load washer models covered by the linked US Product Help article

Safe next steps

  1. 1
    Confirm the exact Whirlpool Washing machine No Water Detected model and displayed code before changing settings.
  2. 2
    Complete only the user-accessible checks described in the linked official source.
  3. 3
    Run one controlled test after the check; if the code returns, stop and use the model manual or qualified service.

Step-by-step diagnosis

  1. 1
    Photograph the complete No Water Detected display before changing controls or removing power
  2. 2
    Confirm that the full model number is covered by this scope: Whirlpool front-load washer models covered by the linked US Product Help article
  3. 3
    Confirm that the observed condition matches the published meaning: the washer has not detected incoming water
  4. 4
    Published check — Check the supply valves and visible inlet hoses with water off, then request service if the message returns
  5. 5
    Use the result as the decision point: if the documented condition is corrected, complete only the source-listed check
  6. 6
    if No Water Detected remains, stop and move to exact-model diagnosis
  7. 7
    Published check — If No Water Detected returns after the listed action, do not repeat the same correction indefinitely
  8. 8
    Published check — continue with exact-model diagnosis
  9. 9
    Use the result as the decision point: if the documented condition is corrected, complete only the source-listed check; if No Water Detected remains, stop and move to exact-model diagnosis

Evidence-backed actions

  1. 1
    Check the supply valves and visible inlet hoses with water off, then request service if the message returns
  2. 2
    If No Water Detected returns after the listed action, do not repeat the same correction indefinitely
  3. 3
    continue with exact-model diagnosis
  4. 4
    If No Water Detected returns after the listed action, do not repeat the same correction indefinitely; continue with exact-model diagnosis

Repair planning

€Cost for the first check
No Water Detected cost planning: €0 for a safe external inspection; typically €15–€80 for a confirmed external hose or seal. Internal leak diagnosis is commonly €90–€220 before parts.
⏱Time for the first check
No Water Detected time plan: 5–15 minutes to shut off water and inspect externally; allow 30–90 minutes for professional leak tracing.
🔧Tools
Dry towels and a shallow tray, Flashlight for external connections, Access to the water shut-off
▣Parts or consumables
No Water Detected parts decision: No part can be selected until the leak location is found. A visibly damaged external hose or seal must match the full Whirlpool model and connection type.

What not to do

  • Do not run another cycle to reproduce an active leak, tilt the appliance, bypass a float switch, or energize wet electrical areas
  • Close the water valves before disconnecting a hose
  • Do not probe the inlet valve electrically or run repeated fill tests if a connection leaks
  • Do not turn No Water Detected into a parts diagnosis
  • the display identifies a condition, not a completed component test
  • Do not turn No Water Detected into a parts diagnosis; the display identifies a condition, not a completed component test

Preventive maintenance

  • 1
    Keep user-accessible filters, seals, hoses, and drain connections clean and inspect them periodically for damage or seepage
  • 2
    Keep inlet hoses unkinked, close household valves before hose work, and clean only user-accessible inlet screens at the exact-model interval
  • 3
    If No Water Detected begins recurring despite the documented maintenance, stop repeating the same action and request exact-model diagnosis

Frequently asked questions

What exactly does No Water Detected identify?

Whirlpool identifies it as the washer has not detected incoming water.

Which action is actually supported for No Water Detected?

Check the supply valves and visible inlet hoses with water off, then request service if the message returns; If No Water Detected returns after the listed action, do not repeat the same correction indefinitely; continue with exact-model diagnosis.

What result matters after the No Water Detected check?

Whether the documented condition clears after the listed action. If it remains or returns, the exact model needs further diagnosis.

Does No Water Detected prove which part failed?

No. It identifies “the washer has not detected incoming water”; parts are selected only after the exact model and failed function are confirmed.

What information should accompany a service request?

The No Water Detected photo, full model and serial number, the operating stage when it appeared, and the result of each published check.

Related faults

Compare related codes for the same appliance or manufacturer before replacing parts.