Appliance guides

Washing machine error codes and fault guides

Browse 229 published, evidence-gated Washing machine guides. Each page states the supported model and region, official source, safe checks, and the point to stop.

229Published guides
5Current page
10Total pages
Verified catalog

Washing machine fault guides

97–120 of 229

GorenjeLow risk
Washing machineE92

The washing machine needs the published drum-cleaning maintenance cycle

Gorenje uses E92 as a drum-cleaning warning. Clean the user-accessible detergent, hose, gasket, and pump-filter areas, then run Ultra clean empty.

GorenjeHigh attention
Washing machineE:02

The washing machine cannot confirm that the door is locked

Gorenje identifies E:02 as a door-lock error in manual 904001en. Check the door closure once, then isolate power and use service if the code returns.

GorenjeHigh attention
Washing machineE:03

The washing machine is not receiving water within the expected filling conditions

Gorenje identifies E:03 as a water-filling error. Check the tap, inlet filter, hose, and published pressure range before one controlled resume.

GorenjeHigh attention
Washing machineE:07

The washing machine cannot drain water through the expected route

Gorenje identifies E:07 as a water-draining error. Inspect the pump filter, hose, drain, and hose height before one controlled resume.

GorenjeUrgent
Washing machineE:09

The washer has detected a possible water leak in or around the appliance

Gorenje identifies E:09 as water detected in the washing-machine area. Inspect only the exterior and stop if a leak is visible.

GorenjeHigh attention
Washing machineE:12

The washer motor-control system has detected a fault or an abnormal load condition

Gorenje identifies E:12 as a motor-control error. Redistribute stuck or tangled laundry once, then use service if the code returns.

GorenjeHigh attention
Washing machineE:23 / E:24

The washer cannot unlock the door after the programme or interruption

Gorenje groups E:23 and E:24 as door-unlocking errors. Turn the washer off and on once; recurring codes need service.

GorenjeLow risk
Washing machineE_AC

the Anti-crease function is active

E_AC is identified by Gorenje support as the Anti-crease function is active. Follow the official, model-scoped checks and service boundary below.

GorenjeCheck soon
Washing machineE_CLF

a reduced-flow washing-machine drain-system alert

E_CLF is identified by Gorenje support as a reduced-flow washing-machine drain-system alert. Follow the official, model-scoped checks and service boundary below.

GorenjeLow risk
Washing machineE_CLn

the washing-machine Drum Clean maintenance warning

E_CLn is identified by Gorenje support as the washing-machine Drum Clean maintenance warning. Follow the official, model-scoped checks and service boundary below.

GorenjeCheck soon
Washing machineE_Fd

excessive foam in the washing machine

E_Fd is identified by Gorenje support as excessive foam in the washing machine. Follow the official, model-scoped checks and service boundary below.

GorenjeCheck soon
Washing machineE_PF

a washing-machine power-supply failure warning

E_PF is identified by Gorenje support as a washing-machine power-supply failure warning. Follow the official, model-scoped checks and service boundary below.

GorenjeUrgent
Washing machineE_UHi

washing-machine voltage above 260 V

E_UHi is identified by Gorenje support as washing-machine voltage above 260 V. Follow the official, model-scoped checks and service boundary below.

GorenjeUrgent
Washing machineE_ULo

washing-machine voltage below 180 V

E_ULo is identified by Gorenje support as washing-machine voltage below 180 V. Follow the official, model-scoped checks and service boundary below.

HaierCheck soon
Washing machineE5

drainage abnormality

E5 is identified by Haier support as drainage abnormality. Follow the official, model-scoped checks and service boundary below.

HaierUrgent
Washing machineErr8

Water level exceeds the maximum

Err8 is described by Haier support as water level exceeds the maximum. Exact checks and component access vary by model and region.

HaierUrgent
Washing machineFb

Leakage or float switch has been triggered

Fb is described by Haier support as leakage or float switch has been triggered. Exact checks and component access vary by model and region.

HaierUrgent
Washing machineFb

water leakage with the float switch triggered on models with a bottom cover

Fb is identified by Haier support as water leakage with the float switch triggered on models with a bottom cover. Follow the official, model-scoped checks and service boundary below.

HotpointHigh attention
Washing machineF01

an electronic circuit-board fault that can make functions unavailable

F01 is identified in Hotpoint's official United Kingdom appliance-specific table as an electronic circuit-board fault that can make functions unavailable. Use only the published external check or service boundary below.

HotpointHigh attention
Washing machineF02

a motor-circuit fault associated with intermittent or absent drum rotation

F02 is identified in Hotpoint's official United Kingdom appliance-specific table as a motor-circuit fault associated with intermittent or absent drum rotation. Use only the published external check or service boundary below.

HotpointHigh attention
Washing machineF03

a temperature-sensing fault that can prevent normal wash heating

F03 is identified in Hotpoint's official United Kingdom appliance-specific table as a temperature-sensing fault that can prevent normal wash heating. Use only the published external check or service boundary below.

HotpointHigh attention
Washing machineF05

a waste-pipe blockage or pump issue that can leave water in the drum

F05 is identified in Hotpoint's official United Kingdom appliance-specific table as a waste-pipe blockage or pump issue that can leave water in the drum. Use only the published external check or service boundary below.

HotpointHigh attention
Washing machineF06

a door-lock fault that can prevent the door closing or the cycle starting

F06 is identified in Hotpoint's official United Kingdom appliance-specific table as a door-lock fault that can prevent the door closing or the cycle starting. Use only the published external check or service boundary below.

HotpointHigh attention
Washing machineF07

an electronic circuit-board or heating-circuit fault

F07 is identified in Hotpoint's official United Kingdom appliance-specific table as an electronic circuit-board or heating-circuit fault. Use only the published external check or service boundary below.