AEG · Washing machine · Fault guide

AEG Washing machine E10 error

ErrorE10

E10 is identified by AEG support as water-inlet problem. Follow the official, model-scoped checks and service boundary below.

Quick answer

What E10 means

AEG Washing machine E10: water-inlet problem. This interpretation applies to AEG washing-machine models covered by the linked UK support article in United Kingdom / English.

Model scope
AEG washing-machine models covered by the linked UK support article
Region
United Kingdom / English
Verified
✓

Primary evidence: AEG washing-machine E10/E11/C1 support.

Open official source ↗
✓
What the code means

water-inlet problem

Follow the exact model manual. open the water tap, check household flow, inspect the visible inlet hose and clean its accessible filter as the exact model manual permits, then arrange service if the code returns Do not open fixed panels or test live circuits.

Typical symptoms

01E10 is shown on the AEG washing machine display, indicator, or connected app
02The published condition is: water-inlet problem
03The affected fill stage does not receive or confirm the expected water supply while E10 is active
04The important observation is when E10 appears and whether the exact published action changes that condition

Fault area and what the code does not prove

Separate the manufacturer-defined condition from components that still need exact-model diagnosis.

01Manufacturer-defined fault area — water-inlet problem
02E10 does not distinguish household supply, hose, accessible screen, inlet hardware, wiring, or control until the listed checks are completed
03Model boundary — apply this interpretation only to AEG washing-machine models covered by the linked UK support article

Safe next steps

  1. 1
    Confirm the exact AEG Washing machine E10 model and displayed code before changing settings.
  2. 2
    Complete only the user-accessible checks described in the linked official source.
  3. 3
    Run one controlled test after the check; if the code returns, stop and use the model manual or qualified service.

Step-by-step diagnosis

  1. 1
    Photograph the complete E10 display before changing controls or removing power
  2. 2
    Confirm that the full model number is covered by this scope: AEG washing-machine models covered by the linked UK support article
  3. 3
    Confirm that the observed condition matches the published meaning: water-inlet problem
  4. 4
    Published check — open the water tap, check household flow, inspect the visible inlet hose and clean its accessible filter as the exact model manual permits, then arrange service if the code returns
  5. 5
    Stop at the published service boundary after these actions
  6. 6
    do not add a restart or test cycle that AEG does not specify for E10
  7. 7
    Published check — Give service the E10 photo, full model and serial number, when it appeared, and the result of every published external check
  8. 8
    Stop at the published service boundary after these actions; do not add a restart or test cycle that AEG does not specify for E10

Evidence-backed actions

  1. 1
    open the water tap, check household flow, inspect the visible inlet hose and clean its accessible filter as the exact model manual permits, then arrange service if the code returns
  2. 2
    Give service the E10 photo, full model and serial number, when it appeared, and the result of every published external check

Repair planning

€Cost for the first check
E10 cost planning: €0 to open valves, straighten hoses, or clean an accessible screen; typically €15–€60 for a confirmed replacement inlet hose. If E10 returns with normal supply, €90–€220 is a typical Europe planning range for diagnosis before parts; it is not AEG pricing.
⏱Time for the first check
E10 time plan: 10–25 minutes for supply, hose, and accessible-screen checks plus one short fill test.
🔧Tools
Dry towels and a shallow tray, Soft brush for a user-accessible inlet screen only, Hand access to the household water valves
▣Parts or consumables
E10 parts decision: Usually none for the first check. Replace an inlet hose only if it is visibly damaged and the exact AEG model specification confirms the correct hose.

What not to do

  • Close the water valves before disconnecting a hose
  • Do not probe the inlet valve electrically or run repeated fill tests if a connection leaks
  • Do not run an extra test cycle after the source tells you to stop or arrange service for E10

Preventive maintenance

  • 1
    Keep inlet hoses unkinked, close household valves before hose work, and clean only user-accessible inlet screens at the exact-model interval
  • 2
    If E10 begins recurring despite the documented maintenance, stop repeating the same action and request exact-model diagnosis

Frequently asked questions

What exactly does E10 identify?

AEG identifies it as water-inlet problem.

Which action is actually supported for E10?

open the water tap, check household flow, inspect the visible inlet hose and clean its accessible filter as the exact model manual permits, then arrange service if the code returns; Give service the E10 photo, full model and serial number, when it appeared, and the result of every published external check.

Can I run another test after E10?

Not unless the official procedure above explicitly includes it. Complete the safe external actions, then keep the appliance stopped at the service boundary.

Does E10 prove which part failed?

No. It identifies “water-inlet problem”; parts are selected only after the exact model and failed function are confirmed.

What information should accompany a service request?

The E10 photo, full model and serial number, the operating stage when it appeared, and the result of each published check.

Related faults

Compare related codes for the same appliance or manufacturer before replacing parts.