Bosch · Dishwasher · Fault guide

Bosch Dishwasher E16 error

ErrorE16

E16 is identified by Bosch support as an unintended water-inlet condition. Follow the official, model-scoped checks and service boundary below.

Quick answer

What E16 means

Bosch Dishwasher E16: an unintended water-inlet condition. This interpretation applies to Bosch dishwasher models covered by the linked Bosch official error-code support page in United States / English.

Model scope
Bosch dishwasher models covered by the linked Bosch official error-code support page
Region
United States / English
Verified
✓

Primary evidence: Bosch US official home-appliance error-code support.

Open official source ↗
!
Stop and make safe

an unintended water-inlet condition

Isolate the appliance when safe. Close the water tap if the appliance continues filling, isolate power when safe, and arrange Bosch service. Do not open fixed panels or test live circuits.

Typical symptoms

01E16 is shown on the Bosch dishwasher display, indicator, or connected app
02The published condition is: an unintended water-inlet condition
03The affected fill stage does not receive or confirm the expected water supply while E16 is active
04The important observation is when E16 appears and whether the exact published action changes that condition

Fault area and what the code does not prove

Separate the manufacturer-defined condition from components that still need exact-model diagnosis.

01Manufacturer-defined fault area — an unintended water-inlet condition
02E16 does not distinguish household supply, hose, accessible screen, inlet hardware, wiring, or control until the listed checks are completed
03Model boundary — apply this interpretation only to Bosch dishwasher models covered by the linked Bosch official error-code support page

Safe next steps

  1. 1
    Confirm the exact Bosch Dishwasher E16 model and displayed code before taking action.
  2. 2
    Keep the appliance in a safe state and use only the external checks named in the official source.
  3. 3
    If the condition remains, stop and arrange qualified service; do not open panels or bypass a safety device.

Step-by-step diagnosis

  1. 1
    Photograph the complete E16 display before changing controls or removing power
  2. 2
    Confirm that the full model number is covered by this scope: Bosch dishwasher models covered by the linked Bosch official error-code support page
  3. 3
    Confirm that the observed condition matches the published meaning: an unintended water-inlet condition
  4. 4
    Published check — Close the water tap if the appliance continues filling, isolate power when safe, and arrange Bosch service
  5. 5
    Stop at the published service boundary after these actions
  6. 6
    do not add a restart or test cycle that Bosch does not specify for E16
  7. 7
    Published check — Give service the E16 photo, full model and serial number, when it appeared, and the result of every published external check
  8. 8
    Stop at the published service boundary after these actions; do not add a restart or test cycle that Bosch does not specify for E16

Service-safe actions

  1. 1
    Close the water tap if the appliance continues filling, isolate power when safe, and arrange Bosch service
  2. 2
    Give service the E16 photo, full model and serial number, when it appeared, and the result of every published external check

Repair planning

€Cost for the first check
E16 cost planning: €0 for a safe external inspection; typically €15–€80 for a confirmed external hose or seal. Internal leak diagnosis is commonly €90–€220 before parts.
⏱Time for the first check
E16 time plan: 5–15 minutes to shut off water and inspect externally; allow 30–90 minutes for professional leak tracing.
🔧Tools
Dry towels and a shallow tray, Flashlight for external connections, Access to the water shut-off
▣Parts or consumables
E16 parts decision: No part can be selected until the leak location is found. A visibly damaged external hose or seal must match the full Bosch model and connection type.

What not to do

  • Do not run another cycle to reproduce an active leak, tilt the appliance, bypass a float switch, or energize wet electrical areas
  • Do not run an extra test cycle after the source tells you to stop or arrange service for E16

Preventive maintenance

  • 1
    Keep user-accessible filters, seals, hoses, and drain connections clean and inspect them periodically for damage or seepage
  • 2
    If E16 begins recurring despite the documented maintenance, stop repeating the same action and request exact-model diagnosis

Frequently asked questions

What exactly does E16 identify?

Bosch identifies it as an unintended water-inlet condition.

Which action is actually supported for E16?

Close the water tap if the appliance continues filling, isolate power when safe, and arrange Bosch service; Give service the E16 photo, full model and serial number, when it appeared, and the result of every published external check.

Can I run another test after E16?

Not unless the official procedure above explicitly includes it. Complete the safe external actions, then keep the appliance stopped at the service boundary.

Does E16 prove which part failed?

No. It identifies “an unintended water-inlet condition”; parts are selected only after the exact model and failed function are confirmed.

What information should accompany a service request?

The E16 photo, full model and serial number, the operating stage when it appeared, and the result of each published check.

Related faults

Compare related codes for the same appliance or manufacturer before replacing parts.