Bosch Dryer E01 error
E01 is identified by Bosch support as a dryer temperature-sensor condition. Follow the official, model-scoped checks and service boundary below.
What E01 means
Bosch Dryer E01: a dryer temperature-sensor condition. This interpretation applies to Bosch dryer models covered by the linked Bosch official error-code support page in United States / English.
- Model scope
- Bosch dryer models covered by the linked Bosch official error-code support page
- Region
- United States / English
- Verified
a dryer temperature-sensor condition
Isolate the appliance when safe. Stop the dryer, clean only the user-accessible filters described by the model manual, and arrange Bosch service if E01 returns. Do not open fixed panels or test live circuits.
Typical symptoms
Fault area and what the code does not prove
Separate the manufacturer-defined condition from components that still need exact-model diagnosis.
Safe next steps
- 1Confirm the exact Bosch Dryer E01 model and displayed code before taking action.
- 2Keep the appliance in a safe state and use only the external checks named in the official source.
- 3If the condition remains, stop and arrange qualified service; do not open panels or bypass a safety device.
Step-by-step diagnosis
- 1Photograph the complete E01 display before changing controls or removing power
- 2Confirm that the full model number is covered by this scope: Bosch dryer models covered by the linked Bosch official error-code support page
- 3Confirm that the observed condition matches the published meaning: a dryer temperature-sensor condition
- 4Published check — Stop the dryer, clean only the user-accessible filters described by the model manual, and arrange Bosch service if E01 returns
- 5Stop at the published service boundary after these actions
- 6do not add a restart or test cycle that Bosch does not specify for E01
- 7Published check — Give service the E01 photo, full model and serial number, when it appeared, and the result of every published external check
- 8Stop at the published service boundary after these actions; do not add a restart or test cycle that Bosch does not specify for E01
Service-safe actions
- 1Stop the dryer, clean only the user-accessible filters described by the model manual, and arrange Bosch service if E01 returns
- 2Give service the E01 photo, full model and serial number, when it appeared, and the result of every published external check
Repair planning
E01 cost planning: The source-listed external check costs €0. A qualified sensor-system diagnosis is generally planned within €90–€220 before any model-specific part is approved.
E01 time plan: 10–20 minutes for the documented E01 external check; allow 30–90 minutes for measured sensor, wiring, and control diagnosis.
Photo of the complete E01 display, Full model and serial number, The exact-model manual for the published external check, No live sensor-circuit test equipment
E01 parts decision: E01 describes a dryer temperature-sensor condition; it does not prove the sensor itself has failed. A blocked path, connector, wiring, control input, or the measured condition can produce the same reported area.
What not to do
- Do not bridge, heat, cool, wet, or electrically probe a sensor to clear E01
- Do not replace a sensor until its circuit and the condition it measures have been checked
- Do not run an extra test cycle after the source tells you to stop or arrange service for E01
Preventive maintenance
- 1Follow the exact Bosch maintenance schedule for the dryer and keep the model, serial number, and service history available
- 2If E01 begins recurring despite the documented maintenance, stop repeating the same action and request exact-model diagnosis
Frequently asked questions
What exactly does E01 identify?
Bosch identifies it as a dryer temperature-sensor condition.
Which action is actually supported for E01?
Stop the dryer, clean only the user-accessible filters described by the model manual, and arrange Bosch service if E01 returns; Give service the E01 photo, full model and serial number, when it appeared, and the result of every published external check.
Can I run another test after E01?
Not unless the official procedure above explicitly includes it. Complete the safe external actions, then keep the appliance stopped at the service boundary.
Does E01 prove which part failed?
No. It identifies “a dryer temperature-sensor condition”; parts are selected only after the exact model and failed function are confirmed.
What information should accompany a service request?
The E01 photo, full model and serial number, the operating stage when it appeared, and the result of each published check.
Did this guide fix your appliance?
Your anonymous response helps us show which repairs work in the real world. One current response is kept per guide.