Dyson Robot vacuum 360 Vis Nav: Vacuum calibration missing error
360 Vis Nav: Vacuum calibration missing is identified by Dyson support as the robot has not completed its vacuum calibration. Follow the official, model-scoped checks and service boundary below.
What 360 Vis Nav: Vacuum calibration missing means
Dyson Robot vacuum 360 Vis Nav: Vacuum calibration missing: the robot has not completed its vacuum calibration. This interpretation applies to Dyson 360 Vis Nav robot vacuum models covered by the official troubleshooting journey in United States / English.
- Model scope
- Dyson 360 Vis Nav robot vacuum models covered by the official troubleshooting journey
- Region
- United States / English
- Verified
the robot has not completed its vacuum calibration
Follow the exact model manual. Place the robot on its dock, complete the official calibration sequence, and contact Dyson if the calibration fault remains. Do not open fixed panels or test live circuits.
Typical symptoms
Fault area and what the code does not prove
Separate the manufacturer-defined condition from components that still need exact-model diagnosis.
Safe next steps
- 1Confirm the exact Dyson Robot vacuum 360 Vis Nav: Vacuum calibration missing model and displayed code before changing settings.
- 2Complete only the user-accessible checks described in the linked official source.
- 3Run one controlled test after the check; if the code returns, stop and use the model manual or qualified service.
Step-by-step diagnosis
- 1Photograph the complete 360 Vis Nav: Vacuum calibration missing display before changing controls or removing power
- 2Confirm that the full model number is covered by this scope: Dyson 360 Vis Nav robot vacuum models covered by the official troubleshooting journey
- 3Confirm that the observed condition matches the published meaning: the robot has not completed its vacuum calibration
- 4Published check — Place the robot on its dock, complete the official calibration sequence, and contact Dyson if the calibration fault remains
- 5Use the result as the decision point: if the documented condition is corrected, complete only the source-listed check
- 6if 360 Vis Nav: Vacuum calibration missing remains, stop and move to exact-model diagnosis
- 7Published check — If 360 Vis Nav: Vacuum calibration missing returns after the listed action, do not repeat the same correction indefinitely
- 8Published check — continue with exact-model diagnosis
- 9Use the result as the decision point: if the documented condition is corrected, complete only the source-listed check; if 360 Vis Nav: Vacuum calibration missing remains, stop and move to exact-model diagnosis
Evidence-backed actions
- 1Place the robot on its dock, complete the official calibration sequence, and contact Dyson if the calibration fault remains
- 2If 360 Vis Nav: Vacuum calibration missing returns after the listed action, do not repeat the same correction indefinitely
- 3continue with exact-model diagnosis
- 4If 360 Vis Nav: Vacuum calibration missing returns after the listed action, do not repeat the same correction indefinitely; continue with exact-model diagnosis
Repair planning
360 Vis Nav: Vacuum calibration missing cost planning: €0 for cleaning, reseating, or temperature recovery; an exact-model battery commonly costs €35–€130. Charging-board or dock diagnosis is commonly €60–€140 before parts.
360 Vis Nav: Vacuum calibration missing time plan: 10–20 minutes for dry contact, seating, and connection checks; add the manufacturer-specified cooling or charging wait before retesting.
Dry microfiber cloth for charging contacts, Exact-model battery removal instructions, No live electrical test equipment
360 Vis Nav: Vacuum calibration missing parts decision: Use only the exact-model battery or charging accessory approved by Dyson, and only when the published procedure or a confirmed diagnosis requires replacement.
What not to do
- Do not charge a wet, swollen, damaged, very hot, or very cold battery
- Do not substitute an unapproved charger or bridge charging contacts
- Do not turn 360 Vis Nav: Vacuum calibration missing into a parts diagnosis
- the display identifies a condition, not a completed component test
- Do not turn 360 Vis Nav: Vacuum calibration missing into a parts diagnosis; the display identifies a condition, not a completed component test
Preventive maintenance
- 1Keep charging contacts clean and dry, store and charge the battery within the specified temperature range, and use only approved charging accessories
- 2If 360 Vis Nav: Vacuum calibration missing begins recurring despite the documented maintenance, stop repeating the same action and request exact-model diagnosis
Frequently asked questions
What exactly does 360 Vis Nav: Vacuum calibration missing identify?
Dyson identifies it as the robot has not completed its vacuum calibration.
Which action is actually supported for 360 Vis Nav: Vacuum calibration missing?
Place the robot on its dock, complete the official calibration sequence, and contact Dyson if the calibration fault remains; If 360 Vis Nav: Vacuum calibration missing returns after the listed action, do not repeat the same correction indefinitely; continue with exact-model diagnosis.
What result matters after the 360 Vis Nav: Vacuum calibration missing check?
Whether the documented condition clears after the listed action. If it remains or returns, the exact model needs further diagnosis.
Does 360 Vis Nav: Vacuum calibration missing prove which part failed?
No. It identifies “the robot has not completed its vacuum calibration”; parts are selected only after the exact model and failed function are confirmed.
What information should accompany a service request?
The 360 Vis Nav: Vacuum calibration missing photo, full model and serial number, the operating stage when it appeared, and the result of each published check.
Did this guide fix your appliance?
Your anonymous response helps us show which repairs work in the real world. One current response is kept per guide.