Electrolux · Microwave · Fault guide

Electrolux Microwave F131 error

ErrorF131

F131 is identified by Electrolux support as the magnetron sensor temperature is too high. Follow the official, model-scoped checks and service boundary below.

Quick answer

What F131 means

Electrolux Microwave F131: the magnetron sensor temperature is too high. This interpretation applies to Electrolux UK microwave combi-ovens covered by the linked official error-code article in United Kingdom / English.

Model scope
Electrolux UK microwave combi-ovens covered by the linked official error-code article
Region
United Kingdom / English
Verified
✓

Primary evidence: Electrolux UK microwave-combi-oven error-code support.

Open official source ↗
!
Stop and make safe

the magnetron sensor temperature is too high

Isolate the appliance when safe. turn the microwave combi-oven off, allow it to cool and arrange service if the code returns Do not open fixed panels or test live circuits.

Typical symptoms

01F131 is shown on the Electrolux microwave display, indicator, or connected app
02The published condition is: the magnetron sensor temperature is too high
03The control cannot confirm the documented measured condition or sensor reference represented by F131
04The important observation is when F131 appears and whether the exact published action changes that condition

Fault area and what the code does not prove

Separate the manufacturer-defined condition from components that still need exact-model diagnosis.

01Manufacturer-defined fault area — the magnetron sensor temperature is too high
02F131 identifies a measured-condition or sensor path, not a completed proof that the sensor itself failed
03Model boundary — apply this interpretation only to Electrolux UK microwave combi-ovens covered by the linked official error-code article

Safe next steps

  1. 1
    Confirm the exact Electrolux Microwave F131 model and displayed code before taking action.
  2. 2
    Keep the appliance in a safe state and use only the external checks named in the official source.
  3. 3
    If the condition remains, stop and arrange qualified service; do not open panels or bypass a safety device.

Step-by-step diagnosis

  1. 1
    Photograph the complete F131 display before changing controls or removing power
  2. 2
    Confirm that the full model number is covered by this scope: Electrolux UK microwave combi-ovens covered by the linked official error-code article
  3. 3
    Confirm that the observed condition matches the published meaning: the magnetron sensor temperature is too high
  4. 4
    Published check — turn the microwave combi-oven off, allow it to cool and arrange service if the code returns
  5. 5
    Stop at the published service boundary after these actions
  6. 6
    do not add a restart or test cycle that Electrolux does not specify for F131
  7. 7
    Published check — Give service the F131 photo, full model and serial number, when it appeared, and the result of every published external check
  8. 8
    Stop at the published service boundary after these actions; do not add a restart or test cycle that Electrolux does not specify for F131

Service-safe actions

  1. 1
    turn the microwave combi-oven off, allow it to cool and arrange service if the code returns
  2. 2
    Give service the F131 photo, full model and serial number, when it appeared, and the result of every published external check

Repair planning

€Cost for the first check
F131 cost planning: The source-listed external check costs €0. A qualified sensor-system diagnosis is generally planned within €90–€220 before any model-specific part is approved.
⏱Time for the first check
F131 time plan: 10–20 minutes for the documented F131 external check; allow 30–90 minutes for measured sensor, wiring, and control diagnosis.
🔧Tools
Photo of the complete F131 display, Full model and serial number, The exact-model manual for the published external check, No live sensor-circuit test equipment
▣Parts or consumables
F131 parts decision: F131 describes the magnetron sensor temperature is too high; it does not prove the sensor itself has failed. A blocked path, connector, wiring, control input, or the measured condition can produce the same reported area.

What not to do

  • Do not bridge, heat, cool, wet, or electrically probe a sensor to clear F131
  • Do not replace a sensor until its circuit and the condition it measures have been checked
  • Do not run an extra test cycle after the source tells you to stop or arrange service for F131

Preventive maintenance

  • 1
    Follow the exact Electrolux maintenance schedule for the microwave and keep the model, serial number, and service history available
  • 2
    If F131 begins recurring despite the documented maintenance, stop repeating the same action and request exact-model diagnosis

Frequently asked questions

What exactly does F131 identify?

Electrolux identifies it as the magnetron sensor temperature is too high.

Which action is actually supported for F131?

turn the microwave combi-oven off, allow it to cool and arrange service if the code returns; Give service the F131 photo, full model and serial number, when it appeared, and the result of every published external check.

Can I run another test after F131?

Not unless the official procedure above explicitly includes it. Complete the safe external actions, then keep the appliance stopped at the service boundary.

Does F131 prove which part failed?

No. It identifies “the magnetron sensor temperature is too high”; parts are selected only after the exact model and failed function are confirmed.

What information should accompany a service request?

The F131 photo, full model and serial number, the operating stage when it appeared, and the result of each published check.

Related faults

Compare related codes for the same appliance or manufacturer before replacing parts.