Hotpoint Dishwasher F07 error
F07 is identified in Hotpoint's official United Kingdom appliance-specific table as a damaged water turbine. Use only the published external check or service boundary below.
a damaged water turbine
Follow only the official Hotpoint instructions for the linked United Kingdom appliance table. Book a Hotpoint engineer and quote F07. Do not open fixed panels, test live wiring, or replace an internal component from the displayed code alone. Stop if there is water, heat, smoke, a burning smell, or unsafe electrical behavior.
Typical symptoms
Fault area and what the code does not prove
Separate the manufacturer-defined condition from components that still need exact-model diagnosis.
Safe next steps
- 1Confirm the exact Hotpoint Dishwasher F07 model and displayed code before taking action.
- 2Keep the appliance in a safe state and use only the external checks named in the official source.
- 3If the condition remains, stop and arrange qualified service; do not open panels or bypass a safety device.
Step-by-step diagnosis
- 1Photograph the complete F07 display before changing controls or removing power
- 2Confirm that the full model number is covered by this scope: Hotpoint dishwasher models covered by the linked UK error-code table
- 3Confirm that the observed condition matches the published meaning: a damaged water turbine
- 4Published check — Book a Hotpoint engineer and quote F07
- 5Published check — Do not open fixed panels, test live wiring, or replace an internal component from the displayed code alone
- 6Stop at the published service boundary after these actions
- 7do not add a restart or test cycle that Hotpoint does not specify for F07
- 8Published check — Give service the F07 photo, full model and serial number, when it appeared, and the result of every published external check
- 9Stop at the published service boundary after these actions; do not add a restart or test cycle that Hotpoint does not specify for F07
Service-safe actions
- 1Book a Hotpoint engineer and quote F07
- 2Do not open fixed panels, test live wiring, or replace an internal component from the displayed code alone
- 3Give service the F07 photo, full model and serial number, when it appeared, and the result of every published external check
Repair planning
F07 cost planning: The source-listed safety check is usually €0. €90–€220 is a typical Europe planning range for diagnosis before parts; it is not Hotpoint pricing. Ask for separate diagnosis, parts, labor, and call-out lines on the quote.
F07 time plan: 5–10 minutes to document and isolate safely; 30–90 minutes is a typical diagnostic visit before any model-specific repair.
Phone camera for the complete F07 display, Full model and serial number, Power or water isolation access as described by the official procedure
F07 parts decision: No component should be ordered from F07 alone. The documented fault area is “a damaged water turbine”; the technician must identify the failed model-specific part and revision.
What not to do
- Do not open fixed panels, test live circuits, bypass protection, or keep operating the appliance after an urgent stop instruction
- Do not run an extra test cycle after the source tells you to stop or arrange service for F07
Preventive maintenance
- 1Follow the exact Hotpoint maintenance schedule for the dishwasher and keep the model, serial number, and service history available
- 2If F07 begins recurring despite the documented maintenance, stop repeating the same action and request exact-model diagnosis
Frequently asked questions
What exactly does F07 identify?
Hotpoint identifies it as a damaged water turbine.
Which action is actually supported for F07?
Book a Hotpoint engineer and quote F07; Do not open fixed panels, test live wiring, or replace an internal component from the displayed code alone; Give service the F07 photo, full model and serial number, when it appeared, and the result of every published external check.
Can I run another test after F07?
Not unless the official procedure above explicitly includes it. Complete the safe external actions, then keep the appliance stopped at the service boundary.
Does F07 prove which part failed?
No. It identifies “a damaged water turbine”; parts are selected only after the exact model and failed function are confirmed.
What information should accompany a service request?
The F07 photo, full model and serial number, the operating stage when it appeared, and the result of each published check.
Did this guide fix your appliance?
Your anonymous response helps us show which repairs work in the real world. One current response is kept per guide.