Miele · Dishwasher · Fault guide

Miele Dishwasher F406 error

ErrorF406

F406 is identified by Miele's official manual as water flow rate insufficient. Follow the exact model-scoped checks and safety boundary below.

Quick answer

What F406 means

Miele Dishwasher F406: water flow rate insufficient. This interpretation applies to Miele laboratory glassware washers covered by operating instructions 01_F6154D09FD151EDCBFA4D957C0C09124 in United States / English.

Model scope
Miele laboratory glassware washers covered by operating instructions 01_F6154D09FD151EDCBFA4D957C0C09124
Region
United States / English
Verified
✓

Primary evidence: Miele official laboratory-dishwasher operating instructions.

Open official source ↗
✓
What the code means

water flow rate insufficient

Isolate the appliance when safe. Do not work on live or pressurised systems.

Typical symptoms

01F406 is shown on the Miele dishwasher display, indicator, or connected app
02The published condition is: water flow rate insufficient
03The appliance has reached the manufacturer-defined stop or service condition associated with F406
04The important observation is when F406 appears and whether the exact published action changes that condition

Fault area and what the code does not prove

Separate the manufacturer-defined condition from components that still need exact-model diagnosis.

01Manufacturer-defined fault area — water flow rate insufficient
02F406 defines a service boundary; the failed internal part still requires exact-model diagnosis
03Model boundary — apply this interpretation only to Miele laboratory glassware washers covered by operating instructions 01_F6154D09FD151EDCBFA4D957C0C09124

Safe next steps

  1. 1
    Confirm the exact Miele Dishwasher F406 model and displayed code before taking action.
  2. 2
    Keep the appliance in a safe state and use only the external checks named in the official source.
  3. 3
    If the condition remains, stop and arrange qualified service; do not open panels or bypass a safety device.

Step-by-step diagnosis

  1. 1
    Photograph the complete F406 display before changing controls or removing power
  2. 2
    Confirm that the full model number is covered by this scope: Miele laboratory glassware washers covered by operating instructions 01_F6154D09FD151EDCBFA4D957C0C09124
  3. 3
    Confirm that the observed condition matches the published meaning: water flow rate insufficient
  4. 4
    Published check — Check that the stopcocks are fully open and the inlet filters are clean
  5. 5
    Published check — have flow pressure checked by a qualified person if required
  6. 6
    Use the result as the decision point: if the documented condition is corrected, complete only the source-listed check
  7. 7
    if F406 remains, stop and move to exact-model diagnosis
  8. 8
    Published check — If F406 returns after the listed action, do not repeat the same correction indefinitely
  9. 9
    Published check — continue with exact-model diagnosis
  10. 10
    Use the result as the decision point: if the documented condition is corrected, complete only the source-listed check; if F406 remains, stop and move to exact-model diagnosis

Service-safe actions

  1. 1
    Check that the stopcocks are fully open and the inlet filters are clean
  2. 2
    have flow pressure checked by a qualified person if required
  3. 3
    If F406 returns after the listed action, do not repeat the same correction indefinitely
  4. 4
    continue with exact-model diagnosis
  5. 5
    If F406 returns after the listed action, do not repeat the same correction indefinitely; continue with exact-model diagnosis

Repair planning

€Cost for the first check
F406 cost planning: €0 to open valves, straighten hoses, or clean an accessible screen; typically €15–€60 for a confirmed replacement inlet hose. If F406 returns with normal supply, €90–€220 is a typical Europe planning range for diagnosis before parts; it is not Miele pricing.
⏱Time for the first check
F406 time plan: 10–25 minutes for supply, hose, and accessible-screen checks plus one short fill test.
🔧Tools
Dry towels and a shallow tray, Soft brush for a user-accessible inlet screen only, Hand access to the household water valves
▣Parts or consumables
F406 parts decision: Usually none for the first check. Replace an inlet hose only if it is visibly damaged and the exact Miele model specification confirms the correct hose.

What not to do

  • Close the water valves before disconnecting a hose
  • Do not probe the inlet valve electrically or run repeated fill tests if a connection leaks
  • Do not turn F406 into a parts diagnosis
  • the display identifies a condition, not a completed component test
  • Do not turn F406 into a parts diagnosis; the display identifies a condition, not a completed component test

Preventive maintenance

  • 1
    Keep inlet hoses unkinked, close household valves before hose work, and clean only user-accessible inlet screens at the exact-model interval
  • 2
    If F406 begins recurring despite the documented maintenance, stop repeating the same action and request exact-model diagnosis

Frequently asked questions

What exactly does F406 identify?

Miele identifies it as water flow rate insufficient.

Which action is actually supported for F406?

Check that the stopcocks are fully open and the inlet filters are clean; have flow pressure checked by a qualified person if required; If F406 returns after the listed action, do not repeat the same correction indefinitely; continue with exact-model diagnosis.

What result matters after the F406 check?

Whether the documented condition clears after the listed action. If it remains or returns, the exact model needs further diagnosis.

Does F406 prove which part failed?

No. It identifies “water flow rate insufficient”; parts are selected only after the exact model and failed function are confirmed.

What information should accompany a service request?

The F406 photo, full model and serial number, the operating stage when it appeared, and the result of each published check.

Related faults

Compare related codes for the same appliance or manufacturer before replacing parts.