iRobot · Robot vacuum · Fault guide

iRobot robot vacuum Charging Error 4 / 5 error

ErrorCharging Error 4 / 5

Charging Error 4 / 5 is identified by iRobot support as the dock or robot has a no-current or low-current charging fault. Follow the model-scoped external checks and service boundary below.

Quick answer

What Charging Error 4 / 5 means

iRobot Robot vacuum Charging Error 4 / 5: The dock or robot has a no-current or low-current charging fault. This interpretation applies to Roomba and Braava models covered by the official iRobot Charging Error Chart 19598 in Global / English.

Model scope
Roomba and Braava models covered by the official iRobot Charging Error Chart 19598
Region
Global / English
Verified
✓

Primary evidence: iRobot official Charging Error Chart.

Open official source ↗
✓
What the code means

The dock or robot has a no-current or low-current charging fault

Follow the exact model manual. Unplug the dock for 60 seconds, secure the power connections, clean the robot and dock charging contacts, then reinstall an authentic battery if the error remains. Do not open fixed panels or test live circuits.

Typical symptoms

01Charging Error 4 / 5 is shown on the iRobot robot vacuum display, indicator, or connected app
02The published condition is: The dock or robot has a no-current or low-current charging fault
03Charging does not start, continue, or complete in the way described for Charging Error 4 / 5
04The important observation is when Charging Error 4 / 5 appears and whether the exact published action changes that condition

Fault area and what the code does not prove

Separate the manufacturer-defined condition from components that still need exact-model diagnosis.

01Manufacturer-defined fault area — The dock or robot has a no-current or low-current charging fault
02Charging Error 4 / 5 does not alone distinguish battery condition, seating, contacts, dock, charger, temperature, or charging electronics
03Model boundary — apply this interpretation only to Roomba and Braava models covered by the official iRobot Charging Error Chart 19598

Safe next steps

  1. 1
    Confirm the exact iRobot Robot vacuum Charging Error 4 / 5 model and displayed code before changing settings.
  2. 2
    Complete only the user-accessible checks described in the linked official source.
  3. 3
    Run one controlled test after the check; if the code returns, stop and use the model manual or qualified service.

Step-by-step diagnosis

  1. 1
    Photograph the complete Charging Error 4 / 5 display before changing controls or removing power
  2. 2
    Confirm that the full model number is covered by this scope: Roomba and Braava models covered by the official iRobot Charging Error Chart 19598
  3. 3
    Confirm that the observed condition matches the published meaning: The dock or robot has a no-current or low-current charging fault
  4. 4
    Published check — Unplug the dock for 60 seconds, secure the power connections, clean the robot and dock charging contacts, then reinstall an authentic battery if the error remains
  5. 5
    Use the result as the decision point: if the documented condition is corrected, complete only the source-listed check; if Charging Error 4 / 5 remains, stop and move to exact-model diagnosis

Evidence-backed actions

  1. 1
    Unplug the dock for 60 seconds, secure the power connections, clean the robot and dock charging contacts, then reinstall an authentic battery if the error remains
  2. 2
    If Charging Error 4 / 5 returns after the listed action, do not repeat the same correction indefinitely; continue with exact-model diagnosis

Repair planning

€Cost for the first check
Charging Error 4 / 5 cost planning: €0 for cleaning, reseating, or temperature recovery; an exact-model battery commonly costs €35–€130. Charging-board or dock diagnosis is commonly €60–€140 before parts.
⏱Time for the first check
Charging Error 4 / 5 time plan: The official action includes for 60 seconds. 10–20 minutes for dry contact, seating, and connection checks; add the manufacturer-specified cooling or charging wait before retesting.
🔧Tools
Dry microfiber cloth for charging contacts, Exact-model battery removal instructions, No live electrical test equipment
▣Parts or consumables
Charging Error 4 / 5 parts decision: Use only the exact-model battery or charging accessory approved by iRobot, and only when the published procedure or a confirmed diagnosis requires replacement.

What not to do

  • Do not charge a wet, swollen, damaged, very hot, or very cold battery
  • Do not substitute an unapproved charger or bridge charging contacts
  • Do not turn Charging Error 4 / 5 into a parts diagnosis; the display identifies a condition, not a completed component test

Preventive maintenance

  • 1
    Keep charging contacts clean and dry, store and charge the battery within the specified temperature range, and use only approved charging accessories
  • 2
    If Charging Error 4 / 5 begins recurring despite the documented maintenance, stop repeating the same action and request exact-model diagnosis

Frequently asked questions

What exactly does Charging Error 4 / 5 identify?

iRobot identifies it as The dock or robot has a no-current or low-current charging fault.

Which action is actually supported for Charging Error 4 / 5?

Unplug the dock for 60 seconds, secure the power connections, clean the robot and dock charging contacts, then reinstall an authentic battery if the error remains.

What result matters after the Charging Error 4 / 5 check?

Whether the documented condition clears after the listed action. If it remains or returns, the exact model needs further diagnosis.

Does Charging Error 4 / 5 prove which part failed?

No. It identifies “The dock or robot has a no-current or low-current charging fault”; parts are selected only after the exact model and failed function are confirmed.

What information should accompany a service request?

The Charging Error 4 / 5 photo, full model and serial number, the operating stage when it appeared, and the result of each published check.

Related faults

Compare related codes for the same appliance or manufacturer before replacing parts.