Samsung · Washing machine · Fault guide

Samsung washer 4C2 / 4E2 / CE / 14C2 / nF1 code

Error4C2 / 4E2 / CE / 14C2 / nF1

4C2 / 4E2 / CE / 14C2 / nF1 is listed by Samsung support as hot and cold water supply lines are reversed. Code variants and available checks can differ by model and region.

Quick answer

What 4C2 / 4E2 / CE / 14C2 / nF1 means

Samsung Washing machine 4C2 / 4E2 / CE / 14C2 / nF1: Hot and cold water supply lines are reversed. This interpretation applies to Samsung washing-machine models listed by the linked official code table in US / English.

Model scope
Samsung washing-machine models listed by the linked official code table
Region
US / English
Verified
✓

Primary evidence: Samsung US washing machine information codes.

Open official source ↗
✓
What the code means

Hot and cold water supply lines are reversed

Disconnect power before inspecting hoses or accessible filters, keep hands away from moving parts, and follow the exact Samsung model manual.

Typical symptoms

014C2 / 4E2 / CE / 14C2 / nF1 appears on the display
02The current cycle may pause or stop
03The affected fill, drain, door, power, or balance function may not complete

Likely causes

Start with the least invasive explanation and stop if the check requires internal electrical or sealed-system access.

01Hot and cold hoses connected to the wrong inlets
02Installation or model-specific temperature-supply configuration

Safe next steps

  1. 1
    Confirm the exact Samsung Washing machine 4C2 / 4E2 / CE / 14C2 / nF1 model and displayed code before changing settings.
  2. 2
    Complete only the user-accessible checks described in the linked official source.
  3. 3
    Run one controlled test after the check; if the code returns, stop and use the model manual or qualified service.

Step-by-step diagnosis

  1. 1
    Photograph the complete 4C2 / 4E2 / CE / 14C2 / nF1 display before changing controls or removing power
  2. 2
    Confirm that the full model number is covered by this scope: Samsung washing-machine models listed by the linked official code table
  3. 3
    Confirm that the observed condition matches the published meaning: Hot and cold water supply lines are reversed
  4. 4
    Turn the washer off
  5. 5
    Confirm that the cold-water supply hose is connected firmly to the cold-water tap
  6. 6
    Check the hose labels before moving any connection
  7. 7
    Restart the cycle once after correcting the connection
  8. 8
    Contact Samsung service if the code remains
  9. 9
    Published check — Close the water taps before moving a hose
  10. 10
    Published check — Reconnect the cold-water hose to the cold-water tap and tighten by hand according to the manual

Evidence-backed actions

  1. 1
    Close the water taps before moving a hose
  2. 2
    Reconnect the cold-water hose to the cold-water tap and tighten by hand according to the manual
  3. 3
    Open the taps and inspect for drips
  4. 4
    Restart one cycle
  5. 5
    Stop if a connection leaks or the code returns
  6. 6
    If 4C2 / 4E2 / CE / 14C2 / nF1 returns after the listed action, do not repeat the same correction indefinitely; continue with exact-model diagnosis

Repair planning

€Cost for the first check
4C2 / 4E2 / CE / 14C2 / nF1 cost planning: €0 to open valves, straighten hoses, or clean an accessible screen; typically €15–€60 for a confirmed replacement inlet hose. If 4C2 / 4E2 / CE / 14C2 / nF1 returns with normal supply, €90–€220 is a typical Europe planning range for diagnosis before parts; it is not Samsung pricing.
⏱Time for the first check
4C2 / 4E2 / CE / 14C2 / nF1 time plan: 10–25 minutes for supply, hose, and accessible-screen checks plus one short fill test.
🔧Tools
Dry towels and a shallow tray, Soft brush for a user-accessible inlet screen only, Hand access to the household water valves
▣Parts or consumables
4C2 / 4E2 / CE / 14C2 / nF1 parts decision: Usually none for the first check. Replace an inlet hose only if it is visibly damaged and the exact Samsung model specification confirms the correct hose.

What not to do

  • Close the water valves before disconnecting a hose
  • Do not probe the inlet valve electrically or run repeated fill tests if a connection leaks
  • Do not swap hoses while water is on
  • Do not overtighten plastic connectors
  • Do not open internal electrical panels
  • Do not turn 4C2 / 4E2 / CE / 14C2 / nF1 into a parts diagnosis; the display identifies a condition, not a completed component test

Preventive maintenance

  • 1
    Keep inlet hoses unkinked, close household valves before hose work, and clean only user-accessible inlet screens at the exact-model interval
  • 2
    Check hose labels after installation or moving the washer
  • 3
    Inspect supply hoses regularly for damage or leaks
  • 4
    If 4C2 / 4E2 / CE / 14C2 / nF1 begins recurring despite the documented maintenance, stop repeating the same action and request exact-model diagnosis

Frequently asked questions

What exactly does 4C2 / 4E2 / CE / 14C2 / nF1 identify?

Samsung identifies it as Hot and cold water supply lines are reversed.

Which action is actually supported for 4C2 / 4E2 / CE / 14C2 / nF1?

Close the water taps before moving a hose; Reconnect the cold-water hose to the cold-water tap and tighten by hand according to the manual; Open the taps and inspect for drips; Restart one cycle; Stop if a connection leaks or the code returns.

What result matters after the 4C2 / 4E2 / CE / 14C2 / nF1 check?

Whether the documented condition clears after the listed action. If it remains or returns, the exact model needs further diagnosis.

Does 4C2 / 4E2 / CE / 14C2 / nF1 prove which part failed?

No. It identifies “Hot and cold water supply lines are reversed”; parts are selected only after the exact model and failed function are confirmed.

What information should accompany a service request?

The 4C2 / 4E2 / CE / 14C2 / nF1 photo, full model and serial number, the operating stage when it appeared, and the result of each published check.

Related faults

Compare related codes for the same appliance or manufacturer before replacing parts.