Vaillant · Heat pump · Fault guide

Vaillant Heat pump F.732 error

ErrorF.732

F.732 is identified by Vaillant support as compressor outlet temperature too high. Follow the official, model-scoped checks and service boundary below.

Quick answer

What F.732 means

Vaillant Heat pump F.732: compressor outlet temperature too high. This interpretation applies to Vaillant heat-pump models covered by the linked official UK heat-pump fault-code page in United Kingdom / English.

Model scope
Vaillant heat-pump models covered by the linked official UK heat-pump fault-code page
Region
United Kingdom / English
Verified
✓

Primary evidence: Vaillant UK official heat-pump fault-code support.

Open official source ↗
!
Stop and make safe

compressor outlet temperature too high

Isolate the appliance when safe. Contact the heating installer or Vaillant engineer for flow, filter, sensor, expansion-valve, and refrigerant diagnosis; do not open the casing. Do not open fixed panels or test live circuits.

Typical symptoms

01F.732 is shown on the Vaillant heat pump display, indicator, or connected app
02The published condition is: compressor outlet temperature too high
03The measured temperature condition does not match the operating range represented by F.732
04The important observation is when F.732 appears and whether the exact published action changes that condition

Fault area and what the code does not prove

Separate the manufacturer-defined condition from components that still need exact-model diagnosis.

01Manufacturer-defined fault area — compressor outlet temperature too high
02F.732 identifies the temperature condition but does not alone prove a sensor, airflow, heater, refrigerant, wiring, or control fault
03Model boundary — apply this interpretation only to Vaillant heat-pump models covered by the linked official UK heat-pump fault-code page

Safe next steps

  1. 1
    Confirm the exact Vaillant Heat pump F.732 model and displayed code before taking action.
  2. 2
    Keep the appliance in a safe state and use only the external checks named in the official source.
  3. 3
    If the condition remains, stop and arrange qualified service; do not open panels or bypass a safety device.

Step-by-step diagnosis

  1. 1
    Photograph the complete F.732 display before changing controls or removing power
  2. 2
    Confirm that the full model number is covered by this scope: Vaillant heat-pump models covered by the linked official UK heat-pump fault-code page
  3. 3
    Confirm that the observed condition matches the published meaning: compressor outlet temperature too high
  4. 4
    Published check — Contact the heating installer or Vaillant engineer for flow, filter, sensor, expansion-valve, and refrigerant diagnosis
  5. 5
    Published check — do not open the casing
  6. 6
    Stop at the published service boundary after these actions
  7. 7
    do not add a restart or test cycle that Vaillant does not specify for F.732
  8. 8
    Published check — Give service the F.732 photo, full model and serial number, when it appeared, and the result of every published external check
  9. 9
    Stop at the published service boundary after these actions; do not add a restart or test cycle that Vaillant does not specify for F.732

Service-safe actions

  1. 1
    Contact the heating installer or Vaillant engineer for flow, filter, sensor, expansion-valve, and refrigerant diagnosis
  2. 2
    do not open the casing
  3. 3
    Give service the F.732 photo, full model and serial number, when it appeared, and the result of every published external check

Repair planning

€Cost for the first check
F.732 cost planning: The source-listed external check costs €0. A qualified sensor-system diagnosis is generally planned within €140–€320 before any model-specific part is approved.
⏱Time for the first check
F.732 time plan: 10–20 minutes for the documented F.732 external check; allow 30–90 minutes for measured sensor, wiring, and control diagnosis.
🔧Tools
Photo of the complete F.732 display, Full model and serial number, The exact-model manual for the published external check, No live sensor-circuit test equipment
▣Parts or consumables
F.732 parts decision: F.732 describes compressor outlet temperature too high; it does not prove the sensor itself has failed. A blocked path, connector, wiring, control input, or the measured condition can produce the same reported area.

What not to do

  • Do not bridge, heat, cool, wet, or electrically probe a sensor to clear F.732
  • Do not replace a sensor until its circuit and the condition it measures have been checked
  • Do not run an extra test cycle after the source tells you to stop or arrange service for F.732

Preventive maintenance

  • 1
    Follow the exact Vaillant maintenance schedule for the heat pump and keep the model, serial number, and service history available
  • 2
    If F.732 begins recurring despite the documented maintenance, stop repeating the same action and request exact-model diagnosis

Frequently asked questions

What exactly does F.732 identify?

Vaillant identifies it as compressor outlet temperature too high.

Which action is actually supported for F.732?

Contact the heating installer or Vaillant engineer for flow, filter, sensor, expansion-valve, and refrigerant diagnosis; do not open the casing; Give service the F.732 photo, full model and serial number, when it appeared, and the result of every published external check.

Can I run another test after F.732?

Not unless the official procedure above explicitly includes it. Complete the safe external actions, then keep the appliance stopped at the service boundary.

Does F.732 prove which part failed?

No. It identifies “compressor outlet temperature too high”; parts are selected only after the exact model and failed function are confirmed.

What information should accompany a service request?

The F.732 photo, full model and serial number, the operating stage when it appeared, and the result of each published check.

Related faults

Compare related codes for the same appliance or manufacturer before replacing parts.