Gorenje error codes and fault guides
Browse 82 published, evidence-gated Gorenje guides. Each page states the supported model and region, official source, safe checks, and the point to stop.
Gorenje fault guides
49–72 of 82
The washer is receiving voltage below or above the stated range
Gorenje identifies E40 as mains voltage outside the stated range. Do not test live mains yourself; use a qualified electrician or appliance service.
an incorrect washing-machine mains frequency warning
E41 is identified by Gorenje support as an incorrect washing-machine mains frequency warning. Follow the official, model-scoped checks and service boundary below.
The washing machine cannot drain water normally
Gorenje uses E7 and E7.2 for a water-draining error. The official procedure covers the pump filter, drain hose, drain, and pump impeller.
The washing machine has detected a water leak
Gorenje uses E9 when water leakage is detected. Inspect only the visible exterior and wall siphon, then stop if the leak or code returns.
The washing machine needs the published drum-cleaning maintenance cycle
Gorenje uses E92 as a drum-cleaning warning. Clean the user-accessible detergent, hose, gasket, and pump-filter areas, then run Ultra clean empty.
The washing machine cannot confirm that the door is locked
Gorenje identifies E:02 as a door-lock error in manual 904001en. Check the door closure once, then isolate power and use service if the code returns.
The washing machine is not receiving water within the expected filling conditions
Gorenje identifies E:03 as a water-filling error. Check the tap, inlet filter, hose, and published pressure range before one controlled resume.
The washing machine cannot drain water through the expected route
Gorenje identifies E:07 as a water-draining error. Inspect the pump filter, hose, drain, and hose height before one controlled resume.
The washer has detected a possible water leak in or around the appliance
Gorenje identifies E:09 as water detected in the washing-machine area. Inspect only the exterior and stop if a leak is visible.
The washer motor-control system has detected a fault or an abnormal load condition
Gorenje identifies E:12 as a motor-control error. Redistribute stuck or tangled laundry once, then use service if the code returns.
The washer cannot unlock the door after the programme or interruption
Gorenje groups E:23 and E:24 as door-unlocking errors. Turn the washer off and on once; recurring codes need service.
the Anti-crease function is active
E_AC is identified by Gorenje support as the Anti-crease function is active. Follow the official, model-scoped checks and service boundary below.
a reduced-flow washing-machine drain-system alert
E_CLF is identified by Gorenje support as a reduced-flow washing-machine drain-system alert. Follow the official, model-scoped checks and service boundary below.
the washing-machine Drum Clean maintenance warning
E_CLn is identified by Gorenje support as the washing-machine Drum Clean maintenance warning. Follow the official, model-scoped checks and service boundary below.
excessive foam in the washing machine
E_Fd is identified by Gorenje support as excessive foam in the washing machine. Follow the official, model-scoped checks and service boundary below.
a washing-machine power-supply failure warning
E_PF is identified by Gorenje support as a washing-machine power-supply failure warning. Follow the official, model-scoped checks and service boundary below.
washing-machine voltage above 260 V
E_UHi is identified by Gorenje support as washing-machine voltage above 260 V. Follow the official, model-scoped checks and service boundary below.
washing-machine voltage below 180 V
E_ULo is identified by Gorenje support as washing-machine voltage below 180 V. Follow the official, model-scoped checks and service boundary below.
a wine-cabinet power-board to user-interface communication error
E0 is identified by Gorenje support as a wine-cabinet power-board to user-interface communication error. Follow the official, model-scoped checks and service boundary below.
a wine-cabinet power-board to wireless-card communication error
E2 is identified by Gorenje support as a wine-cabinet power-board to wireless-card communication error. Follow the official, model-scoped checks and service boundary below.
a wine-cabinet wireless-card to power-board communication error
E3 is identified by Gorenje support as a wine-cabinet wireless-card to power-board communication error. Follow the official, model-scoped checks and service boundary below.
a wine-cabinet user-interface to power-board communication error
E8 is identified by Gorenje support as a wine-cabinet user-interface to power-board communication error. Follow the official, model-scoped checks and service boundary below.
a wine-cabinet door-sensor error
E9 is identified by Gorenje support as a wine-cabinet door-sensor error. Follow the official, model-scoped checks and service boundary below.
a wine-cabinet Zone A fan error
F1 is identified by Gorenje support as a wine-cabinet Zone A fan error. Follow the official, model-scoped checks and service boundary below.