AEG · Dryer · Fault guide

AEG Dryer C6 error

ErrorC6

C6 is identified by AEG support as moisture-sensor problem. Follow the official, model-scoped checks and service boundary below.

Quick answer

What C6 means

AEG Dryer C6: moisture-sensor problem. This interpretation applies to AEG tumble-dryer models covered by the linked UK support article in United Kingdom / English.

Model scope
AEG tumble-dryer models covered by the linked UK support article
Region
United Kingdom / English
Verified
✓

Primary evidence: AEG tumble-dryer C6 support.

Open official source ↗
✓
What the code means

moisture-sensor problem

Follow the exact model manual. clean only the user-accessible sensor area as the manual permits and arrange service if the code persists Do not open fixed panels or test live circuits.

Typical symptoms

01C6 is shown on the AEG dryer display, indicator, or connected app
02The published condition is: moisture-sensor problem
03The control cannot confirm the documented measured condition or sensor reference represented by C6
04The important observation is when C6 appears and whether the exact published action changes that condition

Fault area and what the code does not prove

Separate the manufacturer-defined condition from components that still need exact-model diagnosis.

01Manufacturer-defined fault area — moisture-sensor problem
02C6 identifies a measured-condition or sensor path, not a completed proof that the sensor itself failed
03Model boundary — apply this interpretation only to AEG tumble-dryer models covered by the linked UK support article

Safe next steps

  1. 1
    Confirm the exact AEG Dryer C6 model and displayed code before changing settings.
  2. 2
    Complete only the user-accessible checks described in the linked official source.
  3. 3
    Run one controlled test after the check; if the code returns, stop and use the model manual or qualified service.

Step-by-step diagnosis

  1. 1
    Photograph the complete C6 display before changing controls or removing power
  2. 2
    Confirm that the full model number is covered by this scope: AEG tumble-dryer models covered by the linked UK support article
  3. 3
    Confirm that the observed condition matches the published meaning: moisture-sensor problem
  4. 4
    Published check — clean only the user-accessible sensor area as the manual permits and arrange service if the code persists
  5. 5
    Stop at the published service boundary after these actions
  6. 6
    do not add a restart or test cycle that AEG does not specify for C6
  7. 7
    Published check — Give service the C6 photo, full model and serial number, when it appeared, and the result of every published external check
  8. 8
    Stop at the published service boundary after these actions; do not add a restart or test cycle that AEG does not specify for C6

Evidence-backed actions

  1. 1
    clean only the user-accessible sensor area as the manual permits and arrange service if the code persists
  2. 2
    Give service the C6 photo, full model and serial number, when it appeared, and the result of every published external check

Repair planning

€Cost for the first check
C6 cost planning: The source-listed external check costs €0. A qualified sensor-system diagnosis is generally planned within €90–€220 before any model-specific part is approved.
⏱Time for the first check
C6 time plan: 10–20 minutes for the documented C6 external check; allow 30–90 minutes for measured sensor, wiring, and control diagnosis.
🔧Tools
Photo of the complete C6 display, Full model and serial number, The exact-model manual for the published external check, No live sensor-circuit test equipment
▣Parts or consumables
C6 parts decision: C6 describes moisture-sensor problem; it does not prove the sensor itself has failed. A blocked path, connector, wiring, control input, or the measured condition can produce the same reported area.

What not to do

  • Do not bridge, heat, cool, wet, or electrically probe a sensor to clear C6
  • Do not replace a sensor until its circuit and the condition it measures have been checked
  • Do not run an extra test cycle after the source tells you to stop or arrange service for C6

Preventive maintenance

  • 1
    Follow the exact AEG maintenance schedule for the dryer and keep the model, serial number, and service history available
  • 2
    If C6 begins recurring despite the documented maintenance, stop repeating the same action and request exact-model diagnosis

Frequently asked questions

What exactly does C6 identify?

AEG identifies it as moisture-sensor problem.

Which action is actually supported for C6?

clean only the user-accessible sensor area as the manual permits and arrange service if the code persists; Give service the C6 photo, full model and serial number, when it appeared, and the result of every published external check.

Can I run another test after C6?

Not unless the official procedure above explicitly includes it. Complete the safe external actions, then keep the appliance stopped at the service boundary.

Does C6 prove which part failed?

No. It identifies “moisture-sensor problem”; parts are selected only after the exact model and failed function are confirmed.

What information should accompany a service request?

The C6 photo, full model and serial number, the operating stage when it appeared, and the result of each published check.

Related faults

Compare related codes for the same appliance or manufacturer before replacing parts.