Bosch · Dishwasher · Fault guide

Bosch Dishwasher E05 error

ErrorE05

E05 is identified by Bosch support as a dishwasher fill or water-level condition. Follow the official, model-scoped checks and service boundary below.

Quick answer

What E05 means

Bosch Dishwasher E05: a dishwasher fill or water-level condition. This interpretation applies to Bosch dishwasher models covered by the linked Bosch official error-code support page in United States / English.

Model scope
Bosch dishwasher models covered by the linked Bosch official error-code support page
Region
United States / English
Verified
✓

Primary evidence: Bosch US official home-appliance error-code support.

Open official source ↗
✓
What the code means

a dishwasher fill or water-level condition

Isolate the appliance when safe. Check that the water tap is open and the inlet hose is not visibly kinked; arrange Bosch service if E05 returns. Do not open fixed panels or test live circuits.

Typical symptoms

01E05 is shown on the Bosch dishwasher display, indicator, or connected app
02The published condition is: a dishwasher fill or water-level condition
03The affected fill stage does not receive or confirm the expected water supply while E05 is active
04The important observation is when E05 appears and whether the exact published action changes that condition

Fault area and what the code does not prove

Separate the manufacturer-defined condition from components that still need exact-model diagnosis.

01Manufacturer-defined fault area — a dishwasher fill or water-level condition
02E05 does not distinguish household supply, hose, accessible screen, inlet hardware, wiring, or control until the listed checks are completed
03Model boundary — apply this interpretation only to Bosch dishwasher models covered by the linked Bosch official error-code support page

Safe next steps

  1. 1
    Confirm the exact Bosch Dishwasher E05 model and displayed code before changing settings.
  2. 2
    Complete only the user-accessible checks described in the linked official source.
  3. 3
    Run one controlled test after the check; if the code returns, stop and use the model manual or qualified service.

Step-by-step diagnosis

  1. 1
    Photograph the complete E05 display before changing controls or removing power
  2. 2
    Confirm that the full model number is covered by this scope: Bosch dishwasher models covered by the linked Bosch official error-code support page
  3. 3
    Confirm that the observed condition matches the published meaning: a dishwasher fill or water-level condition
  4. 4
    Published check — Check that the water tap is open and the inlet hose is not visibly kinked
  5. 5
    Published check — arrange Bosch service if E05 returns
  6. 6
    Stop at the published service boundary after these actions
  7. 7
    do not add a restart or test cycle that Bosch does not specify for E05
  8. 8
    Published check — Give service the E05 photo, full model and serial number, when it appeared, and the result of every published external check
  9. 9
    Stop at the published service boundary after these actions; do not add a restart or test cycle that Bosch does not specify for E05

Evidence-backed actions

  1. 1
    Check that the water tap is open and the inlet hose is not visibly kinked
  2. 2
    arrange Bosch service if E05 returns
  3. 3
    Give service the E05 photo, full model and serial number, when it appeared, and the result of every published external check

Repair planning

€Cost for the first check
E05 cost planning: €0 to open valves, straighten hoses, or clean an accessible screen; typically €15–€60 for a confirmed replacement inlet hose. If E05 returns with normal supply, €90–€220 is a typical Europe planning range for diagnosis before parts; it is not Bosch pricing.
⏱Time for the first check
E05 time plan: 10–25 minutes for supply, hose, and accessible-screen checks plus one short fill test.
🔧Tools
Dry towels and a shallow tray, Soft brush for a user-accessible inlet screen only, Hand access to the household water valves
▣Parts or consumables
E05 parts decision: Usually none for the first check. Replace an inlet hose only if it is visibly damaged and the exact Bosch model specification confirms the correct hose.

What not to do

  • Close the water valves before disconnecting a hose
  • Do not probe the inlet valve electrically or run repeated fill tests if a connection leaks
  • Do not run an extra test cycle after the source tells you to stop or arrange service for E05

Preventive maintenance

  • 1
    Keep inlet hoses unkinked, close household valves before hose work, and clean only user-accessible inlet screens at the exact-model interval
  • 2
    If E05 begins recurring despite the documented maintenance, stop repeating the same action and request exact-model diagnosis

Frequently asked questions

What exactly does E05 identify?

Bosch identifies it as a dishwasher fill or water-level condition.

Which action is actually supported for E05?

Check that the water tap is open and the inlet hose is not visibly kinked; arrange Bosch service if E05 returns; Give service the E05 photo, full model and serial number, when it appeared, and the result of every published external check.

Can I run another test after E05?

Not unless the official procedure above explicitly includes it. Complete the safe external actions, then keep the appliance stopped at the service boundary.

Does E05 prove which part failed?

No. It identifies “a dishwasher fill or water-level condition”; parts are selected only after the exact model and failed function are confirmed.

What information should accompany a service request?

The E05 photo, full model and serial number, the operating stage when it appeared, and the result of each published check.

Related faults

Compare related codes for the same appliance or manufacturer before replacing parts.