Bosch · Dishwasher · Fault guide

Bosch Dishwasher E6160 error

ErrorE6160

E6160 is identified by Bosch support as the PowerControl controlled lower spray-arm reference position was not found. Follow the official, model-scoped checks and service boundary below.

Quick answer

What E6160 means

Bosch Dishwasher E6160: the PowerControl controlled lower spray-arm reference position was not found. This interpretation applies to Bosch dishwasher models covered by the linked Bosch US error-code support page in United States / English.

Model scope
Bosch dishwasher models covered by the linked Bosch US error-code support page
Region
United States / English
Verified
✓

Primary evidence: Bosch US official dishwasher error-code support.

Open official source ↗
✓
What the code means

the PowerControl controlled lower spray-arm reference position was not found

Isolate the appliance when safe. Do not dismantle the spray-arm drive; contact Bosch Customer Support for the exact model. Do not open fixed panels or test live circuits.

Typical symptoms

01E6160 appears on the dishwasher display
02The the PowerControl controlled lower spray-arm reference position was not found condition may stop, pause, or limit the appliance
03The same code returns when the model-specific condition remains active

Likely causes

Start with the least invasive explanation and stop if the check requires internal electrical or sealed-system access.

01the PowerControl controlled lower spray-arm reference position was not found
02The exact model manual must be used before any internal diagnosis

Safe next steps

  1. 1
    Confirm the exact Bosch Dishwasher E6160 model and displayed code before taking action.
  2. 2
    Keep the appliance in a safe state and use only the external checks named in the official source.
  3. 3
    If the condition remains, stop and arrange qualified service; do not open panels or bypass a safety device.

Step-by-step diagnosis

  1. 1
    Photograph the complete E6160 display before changing controls or removing power
  2. 2
    Confirm that the full model number is covered by this scope: Bosch dishwasher models covered by the linked Bosch US error-code support page
  3. 3
    Confirm that the observed condition matches the published meaning: the PowerControl controlled lower spray-arm reference position was not found
  4. 4
    Published check — Do not dismantle the spray-arm drive
  5. 5
    Published check — contact Bosch Customer Support for the exact model
  6. 6
    Stop at the published service boundary after these actions
  7. 7
    do not add a restart or test cycle that Bosch does not specify for E6160
  8. 8
    Published check — Give service the E6160 photo, full model and serial number, when it appeared, and the result of every published external check
  9. 9
    Stop at the published service boundary after these actions; do not add a restart or test cycle that Bosch does not specify for E6160

Service-safe actions

  1. 1
    Do not dismantle the spray-arm drive
  2. 2
    contact Bosch Customer Support for the exact model
  3. 3
    Give service the E6160 photo, full model and serial number, when it appeared, and the result of every published external check

Repair planning

€Cost for the first check
E6160 cost planning: The source-listed safety check is usually €0. €90–€220 is a typical Europe planning range for diagnosis before parts; it is not Bosch pricing. Ask for separate diagnosis, parts, labor, and call-out lines on the quote.
⏱Time for the first check
E6160 time plan: 5–10 minutes to document and isolate safely; 30–90 minutes is a typical diagnostic visit before any model-specific repair.
🔧Tools
Phone camera for the complete E6160 display, Full model and serial number, Power or water isolation access as described by the official procedure
▣Parts or consumables
E6160 parts decision: No component should be ordered from E6160 alone. The documented fault area is “the PowerControl controlled lower spray-arm reference position was not found”; the technician must identify the failed model-specific part and revision.

What not to do

  • Do not open fixed panels, test live circuits, bypass protection, or keep operating the appliance after an urgent stop instruction
  • Do not run an extra test cycle after the source tells you to stop or arrange service for E6160

Preventive maintenance

  • 1
    Follow the exact Bosch maintenance schedule for the dishwasher and keep the model, serial number, and service history available
  • 2
    If E6160 begins recurring despite the documented maintenance, stop repeating the same action and request exact-model diagnosis

Frequently asked questions

What exactly does E6160 identify?

Bosch identifies it as the PowerControl controlled lower spray-arm reference position was not found.

Which action is actually supported for E6160?

Do not dismantle the spray-arm drive; contact Bosch Customer Support for the exact model; Give service the E6160 photo, full model and serial number, when it appeared, and the result of every published external check.

Can I run another test after E6160?

Not unless the official procedure above explicitly includes it. Complete the safe external actions, then keep the appliance stopped at the service boundary.

Does E6160 prove which part failed?

No. It identifies “the PowerControl controlled lower spray-arm reference position was not found”; parts are selected only after the exact model and failed function are confirmed.

What information should accompany a service request?

The E6160 photo, full model and serial number, the operating stage when it appeared, and the result of each published check.

Related faults

Compare related codes for the same appliance or manufacturer before replacing parts.