GE Appliances · Dishwasher · Fault guide

GE Appliances Dishwasher LEAK DETECTED error

ErrorLEAK DETECTED

LEAK DETECTED is identified by GE Appliances' official support as the leak-detection system has detected a possible leak. Follow the model-scoped checks and service boundary below.

Quick answer

What LEAK DETECTED means

GE Appliances Dishwasher LEAK DETECTED: the leak-detection system has detected a possible leak. This interpretation applies to GE Appliances dishwasher models covered by the official Dishwasher fault-code article; not every code appears on every model in United States / English.

Model scope
GE Appliances dishwasher models covered by the official Dishwasher fault-code article; not every code appears on every model
Region
United States / English
Verified
✓

Primary evidence: GE Appliances dishwasher error-code support.

Open official source ↗
!
Stop and make safe

the leak-detection system has detected a possible leak

Stop the cycle, close the water supply if water is present, isolate power when safe, and contact service; do not run another cycle while the warning remains. Do not open fixed panels or test live circuits.

Typical symptoms

01LEAK DETECTED is shown on the GE Appliances dishwasher display, indicator, or connected app
02The published condition is: the leak-detection system has detected a possible leak
03Leak protection or a water-detection condition is active; the display does not identify the leak location
04The important observation is when LEAK DETECTED appears and whether the exact published action changes that condition

Fault area and what the code does not prove

Separate the manufacturer-defined condition from components that still need exact-model diagnosis.

01Manufacturer-defined fault area — the leak-detection system has detected a possible leak
02LEAK DETECTED confirms the protection condition, not whether the source is a hose, seal, connection, internal component, or installation leak
03Model boundary — apply this interpretation only to GE Appliances dishwasher models covered by the official Dishwasher fault-code article; not every code appears on every model

Safe next steps

  1. 1
    Confirm the exact GE Appliances Dishwasher LEAK DETECTED model and displayed code before taking action.
  2. 2
    Keep the appliance in a safe state and use only the external checks named in the official source.
  3. 3
    If the condition remains, stop and arrange qualified service; do not open panels or bypass a safety device.

Step-by-step diagnosis

  1. 1
    Photograph the complete LEAK DETECTED display before changing controls or removing power
  2. 2
    Confirm that the full model number is covered by this scope: GE Appliances dishwasher models covered by the official Dishwasher fault-code article; not every code appears on every model
  3. 3
    Confirm that the observed condition matches the published meaning: the leak-detection system has detected a possible leak
  4. 4
    Confirm that the full model number is covered by this scope: GE Appliances dishwasher models covered by the official Dishwasher fault-code article
  5. 5
    not every code appears on every model
  6. 6
    Published check — Stop the cycle, close the water supply if water is present, isolate power when safe, and contact service
  7. 7
    Published check — do not run another cycle while the warning remains
  8. 8
    Stop at the published service boundary after these actions
  9. 9
    do not add a restart or test cycle that GE Appliances does not specify for LEAK DETECTED
  10. 10
    Published check — Give service the LEAK DETECTED photo, full model and serial number, when it appeared, and the result of every published external check

Service-safe actions

  1. 1
    Stop the cycle, close the water supply if water is present, isolate power when safe, and contact service
  2. 2
    do not run another cycle while the warning remains
  3. 3
    Give service the LEAK DETECTED photo, full model and serial number, when it appeared, and the result of every published external check

Repair planning

€Cost for the first check
LEAK DETECTED cost planning: €0 for a safe external inspection; typically €15–€80 for a confirmed external hose or seal. Internal leak diagnosis is commonly €90–€220 before parts.
⏱Time for the first check
LEAK DETECTED time plan: 5–15 minutes to shut off water and inspect externally; allow 30–90 minutes for professional leak tracing.
🔧Tools
Dry towels and a shallow tray, Flashlight for external connections, Access to the water shut-off
▣Parts or consumables
LEAK DETECTED parts decision: No part can be selected until the leak location is found. A visibly damaged external hose or seal must match the full GE Appliances model and connection type.

What not to do

  • Do not run another cycle to reproduce an active leak, tilt the appliance, bypass a float switch, or energize wet electrical areas
  • Do not run an extra test cycle after the source tells you to stop or arrange service for LEAK DETECTED

Preventive maintenance

  • 1
    Keep user-accessible filters, seals, hoses, and drain connections clean and inspect them periodically for damage or seepage
  • 2
    If LEAK DETECTED begins recurring despite the documented maintenance, stop repeating the same action and request exact-model diagnosis

Frequently asked questions

What exactly does LEAK DETECTED identify?

GE Appliances identifies it as the leak-detection system has detected a possible leak.

Which action is actually supported for LEAK DETECTED?

Stop the cycle, close the water supply if water is present, isolate power when safe, and contact service; do not run another cycle while the warning remains; Give service the LEAK DETECTED photo, full model and serial number, when it appeared, and the result of every published external check.

Can I run another test after LEAK DETECTED?

Not unless the official procedure above explicitly includes it. Complete the safe external actions, then keep the appliance stopped at the service boundary.

Does LEAK DETECTED prove which part failed?

No. It identifies “the leak-detection system has detected a possible leak”; parts are selected only after the exact model and failed function are confirmed.

What information should accompany a service request?

The LEAK DETECTED photo, full model and serial number, the operating stage when it appeared, and the result of each published check.

Related faults

Compare related codes for the same appliance or manufacturer before replacing parts.