Gorenje · Dishwasher · Fault guide

Gorenje dishwasher F40 error

ErrorF40

Gorenje uses F40 for an inlet-valve leakage condition. Close the water tap immediately and arrange service; do not attempt a valve repair.

Quick answer

What F40 means

Gorenje Dishwasher F40: The dishwasher inlet valve is leaking. This interpretation applies to Gorenje dishwasher model GV693C60UVAD covered by official manual 875524en in Europe / English manual.

Model scope
Gorenje dishwasher model GV693C60UVAD covered by official manual 875524en
Region
Europe / English manual
Verified
✓

Primary evidence: Gorenje official dishwasher manual 875524en.

Open official source ↗
!
Stop and make safe

The dishwasher inlet valve is leaking

Close the water tap immediately and isolate power if water is near electrical connections. Do not leave the dishwasher connected to an active water supply while it leaks.

Typical symptoms

01F40 appears during or after filling
02Water may enter when no programme is running
03The dishwasher may stop to protect against leakage

Likely causes

Start with the least invasive explanation and stop if the check requires internal electrical or sealed-system access.

01A leaking inlet valve
02An inlet connection or hose leak
03A model-specific fill-control fault

Safe next steps

  1. 1
    Confirm the exact Gorenje Dishwasher F40 model and displayed code before taking action.
  2. 2
    Keep the appliance in a safe state and use only the external checks named in the official source.
  3. 3
    If the condition remains, stop and arrange qualified service; do not open panels or bypass a safety device.

Step-by-step diagnosis

  1. 1
    Photograph the complete F40 display before changing controls or removing power
  2. 2
    Confirm that the full model number is covered by this scope: Gorenje dishwasher model GV693C60UVAD covered by official manual 875524en
  3. 3
    Confirm that the observed condition matches the published meaning: The dishwasher inlet valve is leaking
  4. 4
    Confirm F40 and record the exact model
  5. 5
    Close the water tap immediately
  6. 6
    Unplug the dishwasher only after the area is safe and dry
  7. 7
    Inspect only visible hose and connection areas for active leakage
  8. 8
    Do not restart
  9. 9
    arrange qualified Gorenje service
  10. 10
    Published check — Gorenje's F40 instruction is to shut off water and contact service

Service-safe actions

  1. 1
    Gorenje's F40 instruction is to shut off water and contact service
  2. 2
    Do not attempt to rebuild or replace the inlet valve without the exact model service procedure
  3. 3
    Give service the F40 photo, full model and serial number, when it appeared, and the result of every published external check

Repair planning

€Cost for the first check
F40 cost planning: €0 to open valves, straighten hoses, or clean an accessible screen; typically €15–€60 for a confirmed replacement inlet hose. If F40 returns with normal supply, €90–€220 is a typical Europe planning range for diagnosis before parts; it is not Gorenje pricing.
⏱Time for the first check
F40 time plan: 10–25 minutes for supply, hose, and accessible-screen checks plus one short fill test.
🔧Tools
Dry towels and a shallow tray, Soft brush for a user-accessible inlet screen only, Hand access to the household water valves
▣Parts or consumables
F40 parts decision: Usually none for the first check. Replace an inlet hose only if it is visibly damaged and the exact Gorenje model specification confirms the correct hose.

What not to do

  • Close the water valves before disconnecting a hose
  • Do not probe the inlet valve electrically or run repeated fill tests if a connection leaks
  • Do not leave the tap open, run another programme, remove fixed panels, or touch wet electrical connections
  • Do not run an extra test cycle after the source tells you to stop or arrange service for F40

Preventive maintenance

  • 1
    Keep inlet hoses unkinked, close household valves before hose work, and clean only user-accessible inlet screens at the exact-model interval
  • 2
    Inspect visible water connections after installation or movement and keep the shut-off reachable
  • 3
    If F40 begins recurring despite the documented maintenance, stop repeating the same action and request exact-model diagnosis

Frequently asked questions

What exactly does F40 identify?

Gorenje identifies it as The dishwasher inlet valve is leaking.

Which action is actually supported for F40?

Gorenje's F40 instruction is to shut off water and contact service; Do not attempt to rebuild or replace the inlet valve without the exact model service procedure.

Can I run another test after F40?

Not unless the official procedure above explicitly includes it. Complete the safe external actions, then keep the appliance stopped at the service boundary.

Does F40 prove which part failed?

No. It identifies “The dishwasher inlet valve is leaking”; parts are selected only after the exact model and failed function are confirmed.

What information should accompany a service request?

The F40 photo, full model and serial number, the operating stage when it appeared, and the result of each published check.

Related faults

Compare related codes for the same appliance or manufacturer before replacing parts.