Gorenje · Dishwasher · Fault guide

Gorenje dishwasher F52 error

ErrorF52

Gorenje identifies F52 as a water-level fault. Clean the coarse and fine filters and inspect the external inlet filter before service.

Quick answer

What F52 means

Gorenje Dishwasher F52: The dishwasher has detected an abnormal water level. This interpretation applies to Gorenje dishwasher model GV693C60UVAD covered by official manual 875524en in Europe / English manual.

Model scope
Gorenje dishwasher model GV693C60UVAD covered by official manual 875524en
Region
Europe / English manual
Verified
✓

Primary evidence: Gorenje official dishwasher manual 875524en.

Open official source ↗
✓
What the code means

The dishwasher has detected an abnormal water level

Unplug the dishwasher before removing filters and close the water tap before touching the inlet hose. Stop if the tub is overfilling or leaking.

Typical symptoms

01F52 appears during filling or washing
02The water level may be too low or too high
03The dishwasher may stop before completing the cycle

Likely causes

Start with the least invasive explanation and stop if the check requires internal electrical or sealed-system access.

01Dirty coarse or fine filters
02A blocked external inlet-hose filter
03A water-level sensor or fill fault requiring diagnosis

Safe next steps

  1. 1
    Confirm the exact Gorenje Dishwasher F52 model and displayed code before changing settings.
  2. 2
    Complete only the user-accessible checks described in the linked official source.
  3. 3
    Run one controlled test after the check; if the code returns, stop and use the model manual or qualified service.

Step-by-step diagnosis

  1. 1
    Photograph the complete F52 display before changing controls or removing power
  2. 2
    Confirm that the full model number is covered by this scope: Gorenje dishwasher model GV693C60UVAD covered by official manual 875524en
  3. 3
    Confirm that the observed condition matches the published meaning: The dishwasher has detected an abnormal water level
  4. 4
    Confirm F52 and isolate power
  5. 5
    Remove and clean the coarse and fine filters
  6. 6
    Close the water tap before touching the inlet hose
  7. 7
    Inspect and clean the external inlet-hose filter as the Gorenje manual shows
  8. 8
    Refit parts, reopen the tap, and test once
  9. 9
    arrange service if the water-level code returns
  10. 10
    Published check — Clean the accessible filters and correct only visible inlet restrictions

Evidence-backed actions

  1. 1
    Clean the accessible filters and correct only visible inlet restrictions
  2. 2
    F52 can still require level-sensor or fill diagnosis
  3. 3
    do not replace those parts from the code alone
  4. 4
    If F52 returns after the listed action, do not repeat the same correction indefinitely; continue with exact-model diagnosis

Repair planning

€Cost for the first check
F52 cost planning: €0 to open valves, straighten hoses, or clean an accessible screen; typically €15–€60 for a confirmed replacement inlet hose. If F52 returns with normal supply, €90–€220 is a typical Europe planning range for diagnosis before parts; it is not Gorenje pricing.
⏱Time for the first check
F52 time plan: 10–25 minutes for supply, hose, and accessible-screen checks plus one short fill test.
🔧Tools
Dry towels and a shallow tray, Soft brush for a user-accessible inlet screen only, Hand access to the household water valves
▣Parts or consumables
F52 parts decision: Usually none for the first check. Replace an inlet hose only if it is visibly damaged and the exact Gorenje model specification confirms the correct hose.

What not to do

  • Close the water valves before disconnecting a hose
  • Do not probe the inlet valve electrically or run repeated fill tests if a connection leaks
  • Do not clean filters with power connected, remove a pressurised hose, bypass the water-level system, or continue if the tub overfills
  • Do not turn F52 into a parts diagnosis; the display identifies a condition, not a completed component test

Preventive maintenance

  • 1
    Keep inlet hoses unkinked, close household valves before hose work, and clean only user-accessible inlet screens at the exact-model interval
  • 2
    Clean the filters regularly and keep the external inlet filter accessible for maintenance
  • 3
    If F52 begins recurring despite the documented maintenance, stop repeating the same action and request exact-model diagnosis

Frequently asked questions

What exactly does F52 identify?

Gorenje identifies it as The dishwasher has detected an abnormal water level.

Which action is actually supported for F52?

Clean the accessible filters and correct only visible inlet restrictions; F52 can still require level-sensor or fill diagnosis; do not replace those parts from the code alone.

What result matters after the F52 check?

Whether the documented condition clears after the listed action. If it remains or returns, the exact model needs further diagnosis.

Does F52 prove which part failed?

No. It identifies “The dishwasher has detected an abnormal water level”; parts are selected only after the exact model and failed function are confirmed.

What information should accompany a service request?

The F52 photo, full model and serial number, the operating stage when it appeared, and the result of each published check.

Related faults

Compare related codes for the same appliance or manufacturer before replacing parts.