Gorenje · Washing machine · Fault guide

Gorenje washing machine E3 error

ErrorE3

The Gorenje washing-machine manual uses E3 for a water-filling error. Check the visible supply path and inlet filter against the manual before a single controlled test.

Quick answer

What E3 means

Gorenje Washing machine E3: The washing machine is not filling with water correctly. This interpretation applies to Gorenje washing-machine models covered by official manual 964258en in Europe / English manual.

Model scope
Gorenje washing-machine models covered by official manual 964258en
Region
Europe / English manual
Verified
✓

Primary evidence: Gorenje official washing-machine manual 964258en.

Open official source ↗
✓
What the code means

The washing machine is not filling with water correctly

Close the water tap and unplug the washer before removing the inlet hose or cleaning its filter. Stop immediately if a connection leaks.

Typical symptoms

01E3 appears during the fill stage
02The drum does not reach the expected water level
03The programme pauses or will not continue

Likely causes

Start with the least invasive explanation and stop if the check requires internal electrical or sealed-system access.

01The water tap is closed or the inlet hose is kinked
02The inlet filter is restricted
03Water pressure is outside the manual's stated range

Safe next steps

  1. 1
    Confirm the exact Gorenje Washing machine E3 model and displayed code before changing settings.
  2. 2
    Complete only the user-accessible checks described in the linked official source.
  3. 3
    Run one controlled test after the check; if the code returns, stop and use the model manual or qualified service.

Step-by-step diagnosis

  1. 1
    Photograph the complete E3 display before changing controls or removing power
  2. 2
    Confirm that the full model number is covered by this scope: Gorenje washing-machine models covered by official manual 964258en
  3. 3
    Confirm that the observed condition matches the published meaning: The washing machine is not filling with water correctly
  4. 4
    Confirm the display reads E3 and record the complete model number
  5. 5
    Close the water tap and unplug the washer
  6. 6
    Check that the tap is open, the inlet hose is not kinked, and its accessible filter is clean
  7. 7
    Confirm the household supply can deliver at least 10 litres in 60 seconds and remains within the manual's 0.05–1 MPa range
  8. 8
    Reconnect and run one fill test
  9. 9
    arrange service if E3 returns
  10. 10
    Published check — Correct a closed tap or visible hose restriction and clean the user-accessible inlet filter as the Gorenje manual shows

Evidence-backed actions

  1. 1
    Correct a closed tap or visible hose restriction and clean the user-accessible inlet filter as the Gorenje manual shows
  2. 2
    Do not choose an inlet valve from E3 alone
  3. 3
    use qualified service when the supply is suitable but the code returns
  4. 4
    If E3 returns after the listed action, do not repeat the same correction indefinitely; continue with exact-model diagnosis

Repair planning

€Cost for the first check
E3 cost planning: €0 to open valves, straighten hoses, or clean an accessible screen; typically €15–€60 for a confirmed replacement inlet hose. If E3 returns with normal supply, €90–€220 is a typical Europe planning range for diagnosis before parts; it is not Gorenje pricing.
⏱Time for the first check
E3 time plan: 10–25 minutes for supply, hose, and accessible-screen checks plus one short fill test.
🔧Tools
Dry towels and a shallow tray, Soft brush for a user-accessible inlet screen only, Hand access to the household water valves
▣Parts or consumables
E3 parts decision: Usually none for the first check. Replace an inlet hose only if it is visibly damaged and the exact Gorenje model specification confirms the correct hose.

What not to do

  • Close the water valves before disconnecting a hose
  • Do not probe the inlet valve electrically or run repeated fill tests if a connection leaks
  • Do not remove a pressurised hose, work on live wiring, force the filter, or continue if the hose connection leaks
  • Do not turn E3 into a parts diagnosis; the display identifies a condition, not a completed component test

Preventive maintenance

  • 1
    Keep inlet hoses unkinked, close household valves before hose work, and clean only user-accessible inlet screens at the exact-model interval
  • 2
    Keep the inlet filter and hose free from scale and kinks, and keep the water shut-off accessible
  • 3
    If E3 begins recurring despite the documented maintenance, stop repeating the same action and request exact-model diagnosis

Frequently asked questions

What exactly does E3 identify?

Gorenje identifies it as The washing machine is not filling with water correctly.

Which action is actually supported for E3?

Correct a closed tap or visible hose restriction and clean the user-accessible inlet filter as the Gorenje manual shows; Do not choose an inlet valve from E3 alone; use qualified service when the supply is suitable but the code returns.

What result matters after the E3 check?

Whether the documented condition clears after the listed action. If it remains or returns, the exact model needs further diagnosis.

Does E3 prove which part failed?

No. It identifies “The washing machine is not filling with water correctly”; parts are selected only after the exact model and failed function are confirmed.

What information should accompany a service request?

The E3 photo, full model and serial number, the operating stage when it appeared, and the result of each published check.

Related faults

Compare related codes for the same appliance or manufacturer before replacing parts.