Hotpoint · Dishwasher · Fault guide

Hotpoint dishwasher F01 code

ErrorF01

F01 is described by Hotpoint support as anti-flooding overflow protection. Exact checks and component access vary by model and region.

Quick answer

What F01 means

Hotpoint Dishwasher F01: Anti-flooding overflow protection. This interpretation applies to Hotpoint dishwasher models listed by the linked official code table in UK / English.

Model scope
Hotpoint dishwasher models listed by the linked official code table
Region
UK / English
Verified
✓

Primary evidence: Hotpoint UK integrated dishwasher error codes.

Open official source ↗
!
Stop and make safe

Anti-flooding overflow protection

Stop the cycle, close the water supply, and isolate power only if the area is dry and access is safe. Do not tilt or open fixed panels.

Typical symptoms

01F01 is shown on the Hotpoint dishwasher display, indicator, or connected app
02The published condition is: Anti-flooding overflow protection
03Leak protection or a water-detection condition is active; the display does not identify the leak location
04The important observation is when F01 appears and whether the exact published action changes that condition

Fault area and what the code does not prove

Separate the manufacturer-defined condition from components that still need exact-model diagnosis.

01Manufacturer-defined fault area — Anti-flooding overflow protection
02F01 confirms the protection condition, not whether the source is a hose, seal, connection, internal component, or installation leak
03Model boundary — apply this interpretation only to Hotpoint dishwasher models listed by the linked official code table

Safe next steps

  1. 1
    Confirm the exact Hotpoint Dishwasher F01 model and displayed code before taking action.
  2. 2
    Keep the appliance in a safe state and use only the external checks named in the official source.
  3. 3
    If the condition remains, stop and arrange qualified service; do not open panels or bypass a safety device.

Step-by-step diagnosis

  1. 1
    Photograph the complete F01 display before changing controls or removing power
  2. 2
    Confirm that the full model number is covered by this scope: Hotpoint dishwasher models listed by the linked official code table
  3. 3
    Confirm that the observed condition matches the published meaning: Anti-flooding overflow protection
  4. 4
    Stop using the dishwasher
  5. 5
    Record the displayed F01 code and full model number
  6. 6
    Arrange a Hotpoint engineer visit
  7. 7
    Published check — Hotpoint identifies dishwasher F01 as anti-flooding overflow protection and recommends booking an engineer
  8. 8
    Published check — Do not attempt a component repair or restart cycle from this code alone
  9. 9
    Stop at the published service boundary after these actions; do not add a restart or test cycle that Hotpoint does not specify for F01

Service-safe actions

  1. 1
    Hotpoint identifies dishwasher F01 as anti-flooding overflow protection and recommends booking an engineer
  2. 2
    Do not attempt a component repair or restart cycle from this code alone
  3. 3
    Give service the F01 photo, full model and serial number, when it appeared, and the result of every published external check

Repair planning

€Cost for the first check
F01 cost planning: €0 for a safe external inspection; typically €15–€80 for a confirmed external hose or seal. Internal leak diagnosis is commonly €90–€220 before parts.
⏱Time for the first check
F01 time plan: 5–15 minutes to shut off water and inspect externally; allow 30–90 minutes for professional leak tracing.
🔧Tools
Dry towels and a shallow tray, Flashlight for external connections, Access to the water shut-off
▣Parts or consumables
F01 parts decision: No part can be selected until the leak location is found. A visibly damaged external hose or seal must match the full Hotpoint model and connection type.

What not to do

  • Do not run another cycle to reproduce an active leak, tilt the appliance, bypass a float switch, or energize wet electrical areas
  • Do not continue using the dishwasher
  • Do not remove panels, tip the appliance, or bypass overflow protection
  • Do not attempt electrical or water-system repair
  • Do not ignore water around the appliance
  • Do not run an extra test cycle after the source tells you to stop or arrange service for F01

Preventive maintenance

  • 1
    Keep user-accessible filters, seals, hoses, and drain connections clean and inspect them periodically for damage or seepage
  • 2
    Act promptly if water is visible around the dishwasher
  • 3
    Keep the model number and displayed code for the service booking
  • 4
    If F01 begins recurring despite the documented maintenance, stop repeating the same action and request exact-model diagnosis

Frequently asked questions

What exactly does F01 identify?

Hotpoint identifies it as Anti-flooding overflow protection.

Which action is actually supported for F01?

Hotpoint identifies dishwasher F01 as anti-flooding overflow protection and recommends booking an engineer; Do not attempt a component repair or restart cycle from this code alone.

Can I run another test after F01?

Not unless the official procedure above explicitly includes it. Complete the safe external actions, then keep the appliance stopped at the service boundary.

Does F01 prove which part failed?

No. It identifies “Anti-flooding overflow protection”; parts are selected only after the exact model and failed function are confirmed.

What information should accompany a service request?

The F01 photo, full model and serial number, the operating stage when it appeared, and the result of each published check.

Related faults

Compare related codes for the same appliance or manufacturer before replacing parts.