Siemens · Dishwasher · Fault guide

Siemens dishwasher E08 code

ErrorE08

E08 is described by Siemens support as water level in the rinse bath is too low. Exact checks and component access vary by model and region.

Quick answer

What E08 means

Siemens Dishwasher E08: Water level in the rinse bath is too low. This interpretation applies to Siemens dishwasher models listed by the linked official code table in Ireland / English.

Model scope
Siemens dishwasher models listed by the linked official code table
Region
Ireland / English
Verified
✓

Primary evidence: Siemens Ireland dishwasher error codes.

Open official source ↗
✓
What the code means

Water level in the rinse bath is too low

Switch the dishwasher off before cleaning user-accessible parts. Hidden glass may be present near the filter and pump cover.

Typical symptoms

01E08 is shown on the Siemens dishwasher display, indicator, or connected app
02The published condition is: Water level in the rinse bath is too low
03The affected function behaves as described by the manufacturer while E08 is present
04The important observation is when E08 appears and whether the exact published action changes that condition

Fault area and what the code does not prove

Separate the manufacturer-defined condition from components that still need exact-model diagnosis.

01Manufacturer-defined fault area — Water level in the rinse bath is too low
02E08 identifies the documented condition, not a confirmed replacement part
03Model boundary — apply this interpretation only to Siemens dishwasher models listed by the linked official code table

Safe next steps

  1. 1
    Confirm the exact Siemens Dishwasher E08 model and displayed code before changing settings.
  2. 2
    Complete only the user-accessible checks described in the linked official source.
  3. 3
    Run one controlled test after the check; if the code returns, stop and use the model manual or qualified service.

Step-by-step diagnosis

  1. 1
    Photograph the complete E08 display before changing controls or removing power
  2. 2
    Confirm that the full model number is covered by this scope: Siemens dishwasher models listed by the linked official code table
  3. 3
    Confirm that the observed condition matches the published meaning: Water level in the rinse bath is too low
  4. 4
    Open the dishwasher only when the cycle has stopped safely
  5. 5
    Check that bowls or pots have not tipped over and collected water
  6. 6
    Check that dishes are not covering the internal water-intake opening
  7. 7
    Rearrange the load and run one cycle
  8. 8
    Contact Siemens service if E08 returns
  9. 9
    Published check — Siemens identifies E08 as a low water level in the rinse bath
  10. 10
    Published check — Check the loading first: upright bowls or pots can retain water, and dishes can cover the internal water intake

Evidence-backed actions

  1. 1
    Siemens identifies E08 as a low water level in the rinse bath
  2. 2
    Check the loading first: upright bowls or pots can retain water, and dishes can cover the internal water intake
  3. 3
    Rearrange the load, test once, and arrange service if the code returns
  4. 4
    Give service the E08 photo, full model and serial number, when it appeared, and the result of every published external check

Repair planning

€Cost for the first check
E08 cost planning: €0 to open valves, straighten hoses, or clean an accessible screen; typically €15–€60 for a confirmed replacement inlet hose. If E08 returns with normal supply, €90–€220 is a typical Europe planning range for diagnosis before parts; it is not Siemens pricing.
⏱Time for the first check
E08 time plan: 10–25 minutes for supply, hose, and accessible-screen checks plus one short fill test.
🔧Tools
Dry towels and a shallow tray, Soft brush for a user-accessible inlet screen only, Hand access to the household water valves
▣Parts or consumables
E08 parts decision: Usually none for the first check. Replace an inlet hose only if it is visibly damaged and the exact Siemens model specification confirms the correct hose.

What not to do

  • Close the water valves before disconnecting a hose
  • Do not probe the inlet valve electrically or run repeated fill tests if a connection leaks
  • Do not remove internal components
  • Do not open panels or alter water connections
  • Do not continue repeated cycles if the code returns
  • Do not run an extra test cycle after the source tells you to stop or arrange service for E08

Preventive maintenance

  • 1
    Keep inlet hoses unkinked, close household valves before hose work, and clean only user-accessible inlet screens at the exact-model interval
  • 2
    Load bowls and pots so they cannot collect water
  • 3
    Keep the internal water intake clear of dishes
  • 4
    If E08 begins recurring despite the documented maintenance, stop repeating the same action and request exact-model diagnosis

Frequently asked questions

What exactly does E08 identify?

Siemens identifies it as Water level in the rinse bath is too low.

Which action is actually supported for E08?

Siemens identifies E08 as a low water level in the rinse bath; Check the loading first: upright bowls or pots can retain water, and dishes can cover the internal water intake; Rearrange the load, test once, and arrange service if the code returns.

Can I run another test after E08?

Not unless the official procedure above explicitly includes it. Complete the safe external actions, then keep the appliance stopped at the service boundary.

Does E08 prove which part failed?

No. It identifies “Water level in the rinse bath is too low”; parts are selected only after the exact model and failed function are confirmed.

What information should accompany a service request?

The E08 photo, full model and serial number, the operating stage when it appeared, and the result of each published check.

Related faults

Compare related codes for the same appliance or manufacturer before replacing parts.