LG · Dishwasher · Fault guide

LG dishwasher OE error

ErrorOE

LG uses OE when the dishwasher detects a drain issue. The official checks focus on the filter, drain hose, air gap, and disposal connection.

Quick answer

What OE means

LG Dishwasher OE: The dishwasher is not draining correctly. This interpretation applies to LG dishwasher models covered by the linked US OE support article in United States / English.

Model scope
LG dishwasher models covered by the linked US OE support article
Region
United States / English
Verified
✓

Primary evidence: LG US dishwasher OE support.

Open official source ↗
✓
What the code means

The dishwasher is not draining correctly

Switch the dishwasher off and isolate power before reaching into the filter or sump. Do not work on a disposal connection while it can start.

Typical symptoms

01OE appears after or during a cycle
02Water remains in the tub
03The dishwasher stops before completing the programme

Likely causes

Start with the least invasive explanation and stop if the check requires internal electrical or sealed-system access.

01Food residue in the filter or sump
02A kinked or blocked drain hose
03An installation issue at the air gap or disposal connection

Safe next steps

  1. 1
    Confirm the exact LG Dishwasher OE model and displayed code before changing settings.
  2. 2
    Complete only the user-accessible checks described in the linked official source.
  3. 3
    Run one controlled test after the check; if the code returns, stop and use the model manual or qualified service.

Step-by-step diagnosis

  1. 1
    Photograph the complete OE display before changing controls or removing power
  2. 2
    Confirm that the full model number is covered by this scope: LG dishwasher models covered by the linked US OE support article
  3. 3
    Confirm that the observed condition matches the published meaning: The dishwasher is not draining correctly
  4. 4
    Switch the dishwasher off and isolate power
  5. 5
    Clean the accessible filter and sump
  6. 6
    Inspect the drain hose for kinks or blockage
  7. 7
    Check the air gap or disposal connection where fitted
  8. 8
    Run one short drain test and stop if OE returns
  9. 9
    Published check — Clean the filter and sump, correct a visible drain-hose restriction, and confirm the air-gap or disposal connection
  10. 10
    Published check — Test once

Evidence-backed actions

  1. 1
    Clean the filter and sump, correct a visible drain-hose restriction, and confirm the air-gap or disposal connection
  2. 2
    Test once
  3. 3
    arrange LG service if OE remains
  4. 4
    Give service the OE photo, full model and serial number, when it appeared, and the result of every published external check

Repair planning

€Cost for the first check
OE cost planning: €0 for an accessible blockage check; typically €10–€45 for a confirmed hose, cap, or seal. A diagnosed pump repair commonly moves into the €90–€220 service range before parts.
⏱Time for the first check
OE time plan: 15–35 minutes to drain safely, inspect accessible points, refit them, and run one short drain test.
🔧Tools
Dry towels, shallow tray, and household gloves, Flashlight, A coin or hand grip only if the exact-model manual permits opening the user-accessible filter cover
▣Parts or consumables
OE parts decision: Usually none for clearing an accessible filter or hose. A drain pump is not confirmed by OE; match any pump, cover, seal, or hose to the full model only after diagnosis.

What not to do

  • Do not force a jammed pump cover, tip an appliance containing water, or reach into the pump area while power is connected
  • Do not reach into the sump with power connected, force the pump, or dismantle the drain pump
  • Do not run an extra test cycle after the source tells you to stop or arrange service for OE

Preventive maintenance

  • 1
    Keep user-accessible filters, seals, hoses, and drain connections clean and inspect them periodically for damage or seepage
  • 2
    Keep the filter clean and maintain the drain hose, air gap, and disposal connection as LG specifies
  • 3
    If OE begins recurring despite the documented maintenance, stop repeating the same action and request exact-model diagnosis

Frequently asked questions

What exactly does OE identify?

LG identifies it as The dishwasher is not draining correctly.

Which action is actually supported for OE?

Clean the filter and sump, correct a visible drain-hose restriction, and confirm the air-gap or disposal connection; Test once; arrange LG service if OE remains.

Can I run another test after OE?

Not unless the official procedure above explicitly includes it. Complete the safe external actions, then keep the appliance stopped at the service boundary.

Does OE prove which part failed?

No. It identifies “The dishwasher is not draining correctly”; parts are selected only after the exact model and failed function are confirmed.

What information should accompany a service request?

The OE photo, full model and serial number, the operating stage when it appeared, and the result of each published check.

Related faults

Compare related codes for the same appliance or manufacturer before replacing parts.