AEG dishwasher i23 code
i23 is described by AEG support as drain-pump cover loose or missing. Exact checks and component access vary by model and region.
What i23 means
AEG Dishwasher i23: Drain-pump cover loose or missing. This interpretation applies to AEG dishwashers covered by the linked support article in United Kingdom / English.
- Model scope
- AEG dishwashers covered by the linked support article
- Region
- United Kingdom / English
- Verified
Drain-pump cover loose or missing
Switch the dishwasher off before cleaning user-accessible parts. Hidden glass may be present near the filter and pump cover.
Typical symptoms
Fault area and what the code does not prove
Separate the manufacturer-defined condition from components that still need exact-model diagnosis.
Safe next steps
- 1Confirm the exact AEG Dishwasher i23 model and displayed code before changing settings.
- 2Complete only the user-accessible checks described in the linked official source.
- 3Run one controlled test after the check; if the code returns, stop and use the model manual or qualified service.
Step-by-step diagnosis
- 1Photograph the complete i23 display before changing controls or removing power
- 2Confirm that the full model number is covered by this scope: AEG dishwashers covered by the linked support article
- 3Confirm that the observed condition matches the published meaning: Drain-pump cover loose or missing
- 4Stop the dishwasher and disconnect the mains plug
- 5Remove the filter system
- 6Sponge out residual water
- 7Pull the plastic pump cover up at an angle and inspect the impeller and surrounding area for glass, plastic, bones, or other debris
- 8Refit the cover so it is not loose, reinstall the filter, reconnect power, and run one test
- 9Published check — AEG identifies i23 as a loose or missing drain-pump cover
- 10Published check — Its user-accessible procedure is to isolate power, remove the filter and residual water, lift the cover, remove visible foreign objects carefully, refit the cover securely, reinstall the filter, and test once
Evidence-backed actions
- 1AEG identifies i23 as a loose or missing drain-pump cover
- 2Its user-accessible procedure is to isolate power, remove the filter and residual water, lift the cover, remove visible foreign objects carefully, refit the cover securely, reinstall the filter, and test once
- 3Arrange service if i23 returns or the pump cover is damaged
- 4Give service the i23 photo, full model and serial number, when it appeared, and the result of every published external check
Repair planning
i23 cost planning: €0 for an accessible blockage check; typically €10–€45 for a confirmed hose, cap, or seal. A diagnosed pump repair commonly moves into the €90–€220 service range before parts.
i23 time plan: 15–35 minutes to drain safely, inspect accessible points, refit them, and run one short drain test.
Dry towels, shallow tray, and household gloves, Flashlight, A coin or hand grip only if the exact-model manual permits opening the user-accessible filter cover
i23 parts decision: Usually none for clearing an accessible filter or hose. A drain pump is not confirmed by i23; match any pump, cover, seal, or hose to the full model only after diagnosis.
What not to do
- Do not force a jammed pump cover, tip an appliance containing water, or reach into the pump area while power is connected
- Do not work with power connected
- Do not reach into the pump with bare fingers when sharp glass may be present
- Do not force a damaged cover or remove fixed panels
- Do not repeat drain cycles if standing water or leakage remains
- Do not run an extra test cycle after the source tells you to stop or arrange service for i23
Preventive maintenance
- 1Keep user-accessible filters, seals, hoses, and drain connections clean and inspect them periodically for damage or seepage
- 2Remove hard food debris before loading and clean the filter at the interval in the model manual
- 3If i23 begins recurring despite the documented maintenance, stop repeating the same action and request exact-model diagnosis
Frequently asked questions
What exactly does i23 identify?
AEG identifies it as Drain-pump cover loose or missing.
Which action is actually supported for i23?
AEG identifies i23 as a loose or missing drain-pump cover; Its user-accessible procedure is to isolate power, remove the filter and residual water, lift the cover, remove visible foreign objects carefully, refit the cover securely, reinstall the filter, and test once; Arrange service if i23 returns or the pump cover is damaged.
Can I run another test after i23?
Not unless the official procedure above explicitly includes it. Complete the safe external actions, then keep the appliance stopped at the service boundary.
Does i23 prove which part failed?
No. It identifies “Drain-pump cover loose or missing”; parts are selected only after the exact model and failed function are confirmed.
What information should accompany a service request?
The i23 photo, full model and serial number, the operating stage when it appeared, and the result of each published check.
Did this guide fix your appliance?
Your anonymous response helps us show which repairs work in the real world. One current response is kept per guide.