AEG · Dishwasher · Fault guide

AEG dishwasher i24 code

Errori24

i24 is described by AEG support as drain pump blocked by a foreign object. Exact checks and component access vary by model and region.

Quick answer

What i24 means

AEG Dishwasher i24: Drain pump blocked by a foreign object. This interpretation applies to AEG dishwashers covered by the linked support article in United Kingdom / English.

Model scope
AEG dishwashers covered by the linked support article
Region
United Kingdom / English
Verified
✓

Primary evidence: AEG support: dishwasher i24.

Open official source ↗
✓
What the code means

Drain pump blocked by a foreign object

Switch the dishwasher off before cleaning user-accessible parts. Hidden glass may be present near the filter and pump cover.

Typical symptoms

01i24 is shown on the AEG dishwasher display, indicator, or connected app
02The published condition is: Drain pump blocked by a foreign object
03Water or condensate does not leave through the documented drain path as expected while i24 is active
04The important observation is when i24 appears and whether the exact published action changes that condition

Fault area and what the code does not prove

Separate the manufacturer-defined condition from components that still need exact-model diagnosis.

01Manufacturer-defined fault area — Drain pump blocked by a foreign object
02i24 does not distinguish an accessible restriction, hose installation, household drain, pump, wiring, or control until the drain path is checked
03Model boundary — apply this interpretation only to AEG dishwashers covered by the linked support article

Safe next steps

  1. 1
    Confirm the exact AEG Dishwasher i24 model and displayed code before changing settings.
  2. 2
    Complete only the user-accessible checks described in the linked official source.
  3. 3
    Run one controlled test after the check; if the code returns, stop and use the model manual or qualified service.

Step-by-step diagnosis

  1. 1
    Photograph the complete i24 display before changing controls or removing power
  2. 2
    Confirm that the full model number is covered by this scope: AEG dishwashers covered by the linked support article
  3. 3
    Confirm that the observed condition matches the published meaning: Drain pump blocked by a foreign object
  4. 4
    Stop the dishwasher and disconnect the mains plug
  5. 5
    Remove the filter system
  6. 6
    Sponge out residual water
  7. 7
    Pull the plastic pump cover up at an angle and inspect the impeller for a foreign object
  8. 8
    Remove only visible debris carefully, refit the cover and filter, reconnect power, and run one test
  9. 9
    Published check — AEG identifies i24 as a foreign object blocking the drain pump
  10. 10
    Published check — Its published procedure is to isolate power, remove the filter and residual water, inspect the pump cover and impeller, remove visible debris, refit the cover and filter, then test once

Evidence-backed actions

  1. 1
    AEG identifies i24 as a foreign object blocking the drain pump
  2. 2
    Its published procedure is to isolate power, remove the filter and residual water, inspect the pump cover and impeller, remove visible debris, refit the cover and filter, then test once
  3. 3
    Arrange professional help if the code persists
  4. 4
    Give service the i24 photo, full model and serial number, when it appeared, and the result of every published external check

Repair planning

€Cost for the first check
i24 cost planning: €0 for an accessible blockage check; typically €10–€45 for a confirmed hose, cap, or seal. A diagnosed pump repair commonly moves into the €90–€220 service range before parts.
⏱Time for the first check
i24 time plan: 15–35 minutes to drain safely, inspect accessible points, refit them, and run one short drain test.
🔧Tools
Dry towels, shallow tray, and household gloves, Flashlight, A coin or hand grip only if the exact-model manual permits opening the user-accessible filter cover
▣Parts or consumables
i24 parts decision: Usually none for clearing an accessible filter or hose. A drain pump is not confirmed by i24; match any pump, cover, seal, or hose to the full model only after diagnosis.

What not to do

  • Do not force a jammed pump cover, tip an appliance containing water, or reach into the pump area while power is connected
  • Do not work with power connected
  • Do not use sharp tools or force the impeller
  • Do not remove fixed panels or dismantle the pump
  • Do not run repeated cycles if the dishwasher cannot drain
  • Do not run an extra test cycle after the source tells you to stop or arrange service for i24

Preventive maintenance

  • 1
    Keep user-accessible filters, seals, hoses, and drain connections clean and inspect them periodically for damage or seepage
  • 2
    Remove bones, glass, and hard debris before loading and clean the filter regularly
  • 3
    If i24 begins recurring despite the documented maintenance, stop repeating the same action and request exact-model diagnosis

Frequently asked questions

What exactly does i24 identify?

AEG identifies it as Drain pump blocked by a foreign object.

Which action is actually supported for i24?

AEG identifies i24 as a foreign object blocking the drain pump; Its published procedure is to isolate power, remove the filter and residual water, inspect the pump cover and impeller, remove visible debris, refit the cover and filter, then test once; Arrange professional help if the code persists.

Can I run another test after i24?

Not unless the official procedure above explicitly includes it. Complete the safe external actions, then keep the appliance stopped at the service boundary.

Does i24 prove which part failed?

No. It identifies “Drain pump blocked by a foreign object”; parts are selected only after the exact model and failed function are confirmed.

What information should accompany a service request?

The i24 photo, full model and serial number, the operating stage when it appeared, and the result of each published check.

Related faults

Compare related codes for the same appliance or manufacturer before replacing parts.