Beko · Dishwasher · Fault guide

Beko dishwasher E02 code

ErrorE02

E02 is described by Beko support as water supply interruption or inlet filter restriction. Exact checks and component access vary by model and region.

Quick answer

What E02 means

Beko Dishwasher E02: Water supply interruption or inlet filter restriction. This interpretation applies to Beko dishwasher models covered by the linked manual in Türkiye / English translation.

Model scope
Beko dishwasher models covered by the linked manual
Region
Türkiye / English translation
Verified
✓

Primary evidence: Beko official dishwasher error codes.

Open official source ↗
✓
What the code means

Water supply interruption or inlet filter restriction

Switch the dishwasher off before cleaning user-accessible parts. Hidden glass may be present near the filter and pump cover.

Typical symptoms

01E02 is shown on the Beko dishwasher display, indicator, or connected app
02The published condition is: Water supply interruption or inlet filter restriction
03The affected fill stage does not receive or confirm the expected water supply while E02 is active
04The important observation is when E02 appears and whether the exact published action changes that condition

Fault area and what the code does not prove

Separate the manufacturer-defined condition from components that still need exact-model diagnosis.

01Manufacturer-defined fault area — Water supply interruption or inlet filter restriction
02E02 does not distinguish household supply, hose, accessible screen, inlet hardware, wiring, or control until the listed checks are completed
03Model boundary — apply this interpretation only to Beko dishwasher models covered by the linked manual

Safe next steps

  1. 1
    Confirm the exact Beko Dishwasher E02 model and displayed code before changing settings.
  2. 2
    Complete only the user-accessible checks described in the linked official source.
  3. 3
    Run one controlled test after the check; if the code returns, stop and use the model manual or qualified service.

Step-by-step diagnosis

  1. 1
    Photograph the complete E02 display before changing controls or removing power
  2. 2
    Confirm that the full model number is covered by this scope: Beko dishwasher models covered by the linked manual
  3. 3
    Confirm that the observed condition matches the published meaning: Water supply interruption or inlet filter restriction
  4. 4
    Switch the dishwasher off and disconnect power
  5. 5
    Close the water tap
  6. 6
    Check household water supply and the visible inlet hose
  7. 7
    Remove the inlet hose only after the tap is closed, then inspect and clean its inlet filter as the Beko manual shows
  8. 8
    Reconnect water and power, run one short test, and contact authorised service if E02 returns
  9. 9
    Published check — Beko identifies E02 as a water-supply interruption or blocked inlet filter
  10. 10
    Published check — Its published procedure is to isolate power and water, remove the inlet hose, clean the filter, reconnect everything, and test once

Evidence-backed actions

  1. 1
    Beko identifies E02 as a water-supply interruption or blocked inlet filter
  2. 2
    Its published procedure is to isolate power and water, remove the inlet hose, clean the filter, reconnect everything, and test once
  3. 3
    A recurring E02 requires authorised service rather than an inlet-valve replacement from the code alone
  4. 4
    Give service the E02 photo, full model and serial number, when it appeared, and the result of every published external check

Repair planning

€Cost for the first check
E02 cost planning: €0 to open valves, straighten hoses, or clean an accessible screen; typically €15–€60 for a confirmed replacement inlet hose. If E02 returns with normal supply, €90–€220 is a typical Europe planning range for diagnosis before parts; it is not Beko pricing.
⏱Time for the first check
E02 time plan: 10–25 minutes for supply, hose, and accessible-screen checks plus one short fill test.
🔧Tools
Dry towels and a shallow tray, Soft brush for a user-accessible inlet screen only, Hand access to the household water valves
▣Parts or consumables
E02 parts decision: Usually none for the first check. Replace an inlet hose only if it is visibly damaged and the exact Beko model specification confirms the correct hose.

What not to do

  • Close the water valves before disconnecting a hose
  • Do not probe the inlet valve electrically or run repeated fill tests if a connection leaks
  • Do not remove the inlet hose with the tap open
  • Do not work on live wiring
  • Do not force the filter or use sharp tools
  • Do not run the dishwasher with a leaking hose or connection
  • Do not run an extra test cycle after the source tells you to stop or arrange service for E02

Preventive maintenance

  • 1
    Keep inlet hoses unkinked, close household valves before hose work, and clean only user-accessible inlet screens at the exact-model interval
  • 2
    Keep the inlet hose free from kinks and clean its filter at the interval in the model manual
  • 3
    If E02 begins recurring despite the documented maintenance, stop repeating the same action and request exact-model diagnosis

Frequently asked questions

What exactly does E02 identify?

Beko identifies it as Water supply interruption or inlet filter restriction.

Which action is actually supported for E02?

Beko identifies E02 as a water-supply interruption or blocked inlet filter; Its published procedure is to isolate power and water, remove the inlet hose, clean the filter, reconnect everything, and test once; A recurring E02 requires authorised service rather than an inlet-valve replacement from the code alone.

Can I run another test after E02?

Not unless the official procedure above explicitly includes it. Complete the safe external actions, then keep the appliance stopped at the service boundary.

Does E02 prove which part failed?

No. It identifies “Water supply interruption or inlet filter restriction”; parts are selected only after the exact model and failed function are confirmed.

What information should accompany a service request?

The E02 photo, full model and serial number, the operating stage when it appeared, and the result of each published check.

Related faults

Compare related codes for the same appliance or manufacturer before replacing parts.