Bosch · Dishwasher · Fault guide

Bosch Dishwasher E2130 error

ErrorE2130

E2130 is identified by Bosch support as a Zeolite Crystal Dry fan-motor fault. Follow the official, model-scoped checks and service boundary below.

Quick answer

What E2130 means

Bosch Dishwasher E2130: a Zeolite Crystal Dry fan-motor fault. This interpretation applies to Bosch dishwasher models covered by the linked Bosch US error-code support page in United States / English.

Model scope
Bosch dishwasher models covered by the linked Bosch US error-code support page
Region
United States / English
Verified
✓

Primary evidence: Bosch US official dishwasher error-code support.

Open official source ↗
✓
What the code means

a Zeolite Crystal Dry fan-motor fault

Isolate the appliance when safe. Reset power at the breaker for 30 seconds; if the code remains, contact Bosch Customer Support. Do not open fixed panels or test live circuits.

Typical symptoms

01E2130 appears on the dishwasher display
02The a Zeolite Crystal Dry fan-motor fault condition may stop, pause, or limit the appliance
03The same code returns when the model-specific condition remains active

Likely causes

Start with the least invasive explanation and stop if the check requires internal electrical or sealed-system access.

01a Zeolite Crystal Dry fan-motor fault
02The exact model manual must be used before any internal diagnosis

Safe next steps

  1. 1
    Confirm the exact Bosch Dishwasher E2130 model and displayed code before taking action.
  2. 2
    Keep the appliance in a safe state and use only the external checks named in the official source.
  3. 3
    If the condition remains, stop and arrange qualified service; do not open panels or bypass a safety device.

Step-by-step diagnosis

  1. 1
    Photograph the complete E2130 display before changing controls or removing power
  2. 2
    Confirm that the full model number is covered by this scope: Bosch dishwasher models covered by the linked Bosch US error-code support page
  3. 3
    Confirm that the observed condition matches the published meaning: a Zeolite Crystal Dry fan-motor fault
  4. 4
    Published check — Reset power at the breaker for 30 seconds
  5. 5
    Published check — if the code remains, contact Bosch Customer Support
  6. 6
    Stop at the published service boundary after these actions
  7. 7
    do not add a restart or test cycle that Bosch does not specify for E2130
  8. 8
    Published check — Give service the E2130 photo, full model and serial number, when it appeared, and the result of every published external check
  9. 9
    Stop at the published service boundary after these actions; do not add a restart or test cycle that Bosch does not specify for E2130

Service-safe actions

  1. 1
    Reset power at the breaker for 30 seconds
  2. 2
    if the code remains, contact Bosch Customer Support
  3. 3
    Give service the E2130 photo, full model and serial number, when it appeared, and the result of every published external check

Repair planning

€Cost for the first check
E2130 cost planning: €0 for the published breaker, plug, or power-restoration check. If the household supply or appliance wiring needs diagnosis, €90–€220 is a typical Europe planning range for diagnosis before parts; it is not Bosch pricing.
⏱Time for the first check
E2130 time plan: The official action includes for 30 seconds. 5–15 minutes to document E2130 and complete the published power check; allow 30–90 minutes for a qualified supply or appliance diagnosis.
🔧Tools
Phone photo of the complete E2130 display, Full model and serial number, Access to the household breaker or plug only as the official instructions permit, No live-voltage test equipment for an owner check
▣Parts or consumables
E2130 parts decision: E2130 documents a Zeolite Crystal Dry fan-motor fault. It does not by itself distinguish the appliance, cord, outlet, breaker, or installation wiring as the failed item; a qualified electrical check must locate the fault before parts are ordered.

What not to do

  • Do not use an extension lead, bypass a tripping breaker, open a plug or control enclosure, or measure live mains voltage
  • Stop immediately if E2130 follows heat, arcing, smoke, or a burning smell
  • Do not run an extra test cycle after the source tells you to stop or arrange service for E2130

Preventive maintenance

  • 1
    Follow the exact Bosch maintenance schedule for the dishwasher and keep the model, serial number, and service history available
  • 2
    If E2130 begins recurring despite the documented maintenance, stop repeating the same action and request exact-model diagnosis

Frequently asked questions

What exactly does E2130 identify?

Bosch identifies it as a Zeolite Crystal Dry fan-motor fault.

Which action is actually supported for E2130?

Reset power at the breaker for 30 seconds; if the code remains, contact Bosch Customer Support; Give service the E2130 photo, full model and serial number, when it appeared, and the result of every published external check.

Can I run another test after E2130?

Not unless the official procedure above explicitly includes it. Complete the safe external actions, then keep the appliance stopped at the service boundary.

Does E2130 prove which part failed?

No. It identifies “a Zeolite Crystal Dry fan-motor fault”; parts are selected only after the exact model and failed function are confirmed.

What information should accompany a service request?

The E2130 photo, full model and serial number, the operating stage when it appeared, and the result of each published check.

Related faults

Compare related codes for the same appliance or manufacturer before replacing parts.