Bosch · Dishwasher · Fault guide

Bosch Dishwasher E3100 error

ErrorE3100

E3100 is listed by Bosch support as leakage protection detected water in the base. The exact checks and component layout can vary by model and region.

Quick answer

What E3100 means

Bosch Dishwasher E3100: Leakage protection detected water in the base. This interpretation applies to Bosch dishwasher models covered by the linked Bosch US error-code support page in United States / English.

Model scope
Bosch dishwasher models covered by the linked Bosch US error-code support page
Region
United States / English
Verified
✓

Primary evidence: Bosch US official dishwasher error-code support.

Open official source ↗
!
Stop and make safe

Leakage protection detected water in the base

Stop the cycle, close the water supply, and isolate power only if the area is dry and access is safe. Do not tilt or open fixed panels.

Typical symptoms

01The drain pump may continue running with no program selected
02Normal cycles remain locked out
03E3100 indicates water in the dishwasher base and active leak protection

Likely causes

Start with the least invasive explanation and stop if the check requires internal electrical or sealed-system access.

01Leakage protection detected water in the base

Safe next steps

  1. 1
    Confirm the exact Bosch Dishwasher E3100 model and displayed code before taking action.
  2. 2
    Keep the appliance in a safe state and use only the external checks named in the official source.
  3. 3
    If the condition remains, stop and arrange qualified service; do not open panels or bypass a safety device.

Step-by-step diagnosis

  1. 1
    Photograph the complete E3100 display before changing controls or removing power
  2. 2
    Confirm that the full model number is covered by this scope: Bosch dishwasher models covered by the linked Bosch US error-code support page
  3. 3
    Confirm that the observed condition matches the published meaning: Leakage protection detected water in the base
  4. 4
    Confirm that the observed condition matches the published meaning: water detected in the dishwasher base and the leakage-protection system activated
  5. 5
    Published check — Turn off the water inflow immediately and contact Bosch Customer Support
  6. 6
    Published check — do not restart the dishwasher to test for a leak
  7. 7
    Stop at the published service boundary after these actions
  8. 8
    do not add a restart or test cycle that Bosch does not specify for E3100
  9. 9
    Published check — Give service the E3100 photo, full model and serial number, when it appeared, and the result of every published external check
  10. 10
    Stop at the published service boundary after these actions; do not add a restart or test cycle that Bosch does not specify for E3100

Service-safe actions

  1. 1
    Turn off the water inflow immediately and contact Bosch Customer Support
  2. 2
    do not restart the dishwasher to test for a leak
  3. 3
    Give service the E3100 photo, full model and serial number, when it appeared, and the result of every published external check

Repair planning

€Cost for the first check
E3100 cost planning: €0 for a safe external inspection; typically €15–€80 for a confirmed external hose or seal. Internal leak diagnosis is commonly €90–€220 before parts.
⏱Time for the first check
E3100 time plan: 5–15 minutes to shut off water and inspect externally; allow 30–90 minutes for professional leak tracing.
🔧Tools
Dry towels and a shallow tray, Flashlight for external connections, Access to the water shut-off
▣Parts or consumables
E3100 parts decision: No part can be selected until the leak location is found. A visibly damaged external hose or seal must match the full Bosch model and connection type.

What not to do

  • Do not run another cycle to reproduce an active leak, tilt the appliance, bypass a float switch, or energize wet electrical areas
  • Do not run an extra test cycle after the source tells you to stop or arrange service for E3100

Preventive maintenance

  • 1
    Keep user-accessible filters, seals, hoses, and drain connections clean and inspect them periodically for damage or seepage
  • 2
    If E3100 begins recurring despite the documented maintenance, stop repeating the same action and request exact-model diagnosis

Frequently asked questions

What exactly does E3100 identify?

Bosch identifies it as Leakage protection detected water in the base.

Which action is actually supported for E3100?

Turn off the water inflow immediately and contact Bosch Customer Support; do not restart the dishwasher to test for a leak; Give service the E3100 photo, full model and serial number, when it appeared, and the result of every published external check.

Can I run another test after E3100?

Not unless the official procedure above explicitly includes it. Complete the safe external actions, then keep the appliance stopped at the service boundary.

Does E3100 prove which part failed?

No. It identifies “Leakage protection detected water in the base”; parts are selected only after the exact model and failed function are confirmed.

What information should accompany a service request?

The E3100 photo, full model and serial number, the operating stage when it appeared, and the result of each published check.

Related faults

Compare related codes for the same appliance or manufacturer before replacing parts.