Bosch · Dishwasher · Fault guide

Bosch Dishwasher E3000 error

ErrorE3000

E3000 is identified by Bosch support as a flow-meter or dishwasher filling-system fault. Follow the official, model-scoped checks and service boundary below.

Quick answer

What E3000 means

Bosch Dishwasher E3000: a flow-meter or dishwasher filling-system fault. This interpretation applies to Bosch dishwasher models covered by the linked Bosch US error-code support page in United States / English.

Model scope
Bosch dishwasher models covered by the linked Bosch US error-code support page
Region
United States / English
Verified
✓

Primary evidence: Bosch US official dishwasher error-code support.

Open official source ↗
✓
What the code means

a flow-meter or dishwasher filling-system fault

Isolate the appliance when safe. Check the visible water supply only as the model manual permits; if the code remains, contact Bosch Customer Support. Do not open fixed panels or test live circuits.

Typical symptoms

01E3000 appears on the dishwasher display
02The a flow-meter or dishwasher filling-system fault condition may stop, pause, or limit the appliance
03The same code returns when the model-specific condition remains active

Likely causes

Start with the least invasive explanation and stop if the check requires internal electrical or sealed-system access.

01a flow-meter or dishwasher filling-system fault
02The exact model manual must be used before any internal diagnosis

Safe next steps

  1. 1
    Confirm the exact Bosch Dishwasher E3000 model and displayed code before taking action.
  2. 2
    Keep the appliance in a safe state and use only the external checks named in the official source.
  3. 3
    If the condition remains, stop and arrange qualified service; do not open panels or bypass a safety device.

Step-by-step diagnosis

  1. 1
    Photograph the complete E3000 display before changing controls or removing power
  2. 2
    Confirm that the full model number is covered by this scope: Bosch dishwasher models covered by the linked Bosch US error-code support page
  3. 3
    Confirm that the observed condition matches the published meaning: a flow-meter or dishwasher filling-system fault
  4. 4
    Published check — Check the visible water supply only as the model manual permits
  5. 5
    Published check — if the code remains, contact Bosch Customer Support
  6. 6
    Stop at the published service boundary after these actions
  7. 7
    do not add a restart or test cycle that Bosch does not specify for E3000
  8. 8
    Published check — Give service the E3000 photo, full model and serial number, when it appeared, and the result of every published external check
  9. 9
    Stop at the published service boundary after these actions; do not add a restart or test cycle that Bosch does not specify for E3000

Service-safe actions

  1. 1
    Check the visible water supply only as the model manual permits
  2. 2
    if the code remains, contact Bosch Customer Support
  3. 3
    Give service the E3000 photo, full model and serial number, when it appeared, and the result of every published external check

Repair planning

€Cost for the first check
E3000 cost planning: €0 to open valves, straighten hoses, or clean an accessible screen; typically €15–€60 for a confirmed replacement inlet hose. If E3000 returns with normal supply, €90–€220 is a typical Europe planning range for diagnosis before parts; it is not Bosch pricing.
⏱Time for the first check
E3000 time plan: 10–25 minutes for supply, hose, and accessible-screen checks plus one short fill test.
🔧Tools
Dry towels and a shallow tray, Soft brush for a user-accessible inlet screen only, Hand access to the household water valves
▣Parts or consumables
E3000 parts decision: Usually none for the first check. Replace an inlet hose only if it is visibly damaged and the exact Bosch model specification confirms the correct hose.

What not to do

  • Close the water valves before disconnecting a hose
  • Do not probe the inlet valve electrically or run repeated fill tests if a connection leaks
  • Do not run an extra test cycle after the source tells you to stop or arrange service for E3000

Preventive maintenance

  • 1
    Keep inlet hoses unkinked, close household valves before hose work, and clean only user-accessible inlet screens at the exact-model interval
  • 2
    If E3000 begins recurring despite the documented maintenance, stop repeating the same action and request exact-model diagnosis

Frequently asked questions

What exactly does E3000 identify?

Bosch identifies it as a flow-meter or dishwasher filling-system fault.

Which action is actually supported for E3000?

Check the visible water supply only as the model manual permits; if the code remains, contact Bosch Customer Support; Give service the E3000 photo, full model and serial number, when it appeared, and the result of every published external check.

Can I run another test after E3000?

Not unless the official procedure above explicitly includes it. Complete the safe external actions, then keep the appliance stopped at the service boundary.

Does E3000 prove which part failed?

No. It identifies “a flow-meter or dishwasher filling-system fault”; parts are selected only after the exact model and failed function are confirmed.

What information should accompany a service request?

The E3000 photo, full model and serial number, the operating stage when it appeared, and the result of each published check.

Related faults

Compare related codes for the same appliance or manufacturer before replacing parts.