Bosch · Dishwasher · Fault guide

Bosch Dishwasher E6102 error

ErrorE6102

E6102 is listed by Bosch support as drain pump is blocked or its cover is loose. The exact checks and component layout can vary by model and region.

Quick answer

What E6102 means

Bosch Dishwasher E6102: Drain pump is blocked or its cover is loose. This interpretation applies to Bosch dishwasher models covered by the linked Bosch US error-code support page in United States / English.

Model scope
Bosch dishwasher models covered by the linked Bosch US error-code support page
Region
United States / English
Verified
✓

Primary evidence: Bosch US official dishwasher error-code support.

Open official source ↗
✓
What the code means

Drain pump is blocked or its cover is loose

Switch the dishwasher off before cleaning user-accessible parts. Hidden glass may be present near the filter and pump cover.

Typical symptoms

01The drain phase runs but water remains in the tub
02A pump hum may be audible without normal water flow
03The pump cover, drain hose, or air gap may be blocked

Likely causes

Start with the least invasive explanation and stop if the check requires internal electrical or sealed-system access.

01Drain pump is blocked or its cover is loose

Safe next steps

  1. 1
    Confirm the exact Bosch Dishwasher E6102 model and displayed code before changing settings.
  2. 2
    Complete only the user-accessible checks described in the linked official source.
  3. 3
    Run one controlled test after the check; if the code returns, stop and use the model manual or qualified service.

Step-by-step diagnosis

  1. 1
    Photograph the complete E6102 display before changing controls or removing power
  2. 2
    Confirm that the full model number is covered by this scope: Bosch dishwasher models covered by the linked Bosch US error-code support page
  3. 3
    Confirm that the observed condition matches the published meaning: Drain pump is blocked or its cover is loose
  4. 4
    Confirm that the observed condition matches the published meaning: a blocked drain pump or loose or missing pump cover
  5. 5
    Published check — With power isolated, inspect the pump-cover and accessible debris area exactly as Bosch describes
  6. 6
    Published check — contact Bosch if the code returns
  7. 7
    Use the result as the decision point: if the documented condition is corrected, complete only the source-listed check
  8. 8
    if E6102 remains, stop and move to exact-model diagnosis
  9. 9
    Published check — If E6102 returns after the listed action, do not repeat the same correction indefinitely
  10. 10
    Published check — continue with exact-model diagnosis

Evidence-backed actions

  1. 1
    With power isolated, inspect the pump-cover and accessible debris area exactly as Bosch describes
  2. 2
    contact Bosch if the code returns
  3. 3
    If E6102 returns after the listed action, do not repeat the same correction indefinitely
  4. 4
    continue with exact-model diagnosis
  5. 5
    If E6102 returns after the listed action, do not repeat the same correction indefinitely; continue with exact-model diagnosis

Repair planning

€Cost for the first check
E6102 cost planning: €0 for an accessible blockage check; typically €10–€45 for a confirmed hose, cap, or seal. A diagnosed pump repair commonly moves into the €90–€220 service range before parts.
⏱Time for the first check
E6102 time plan: 15–35 minutes to drain safely, inspect accessible points, refit them, and run one short drain test.
🔧Tools
Dry towels, shallow tray, and household gloves, Flashlight, A coin or hand grip only if the exact-model manual permits opening the user-accessible filter cover
▣Parts or consumables
E6102 parts decision: Usually none for clearing an accessible filter or hose. A drain pump is not confirmed by E6102; match any pump, cover, seal, or hose to the full model only after diagnosis.

What not to do

  • Do not force a jammed pump cover, tip an appliance containing water, or reach into the pump area while power is connected
  • Do not turn E6102 into a parts diagnosis
  • the display identifies a condition, not a completed component test
  • Do not turn E6102 into a parts diagnosis; the display identifies a condition, not a completed component test

Preventive maintenance

  • 1
    Keep user-accessible filters, seals, hoses, and drain connections clean and inspect them periodically for damage or seepage
  • 2
    If E6102 begins recurring despite the documented maintenance, stop repeating the same action and request exact-model diagnosis

Frequently asked questions

What exactly does E6102 identify?

Bosch identifies it as Drain pump is blocked or its cover is loose.

Which action is actually supported for E6102?

With power isolated, inspect the pump-cover and accessible debris area exactly as Bosch describes; contact Bosch if the code returns; If E6102 returns after the listed action, do not repeat the same correction indefinitely; continue with exact-model diagnosis.

What result matters after the E6102 check?

Whether the documented condition clears after the listed action. If it remains or returns, the exact model needs further diagnosis.

Does E6102 prove which part failed?

No. It identifies “Drain pump is blocked or its cover is loose”; parts are selected only after the exact model and failed function are confirmed.

What information should accompany a service request?

The E6102 photo, full model and serial number, the operating stage when it appeared, and the result of each published check.

Related faults

Compare related codes for the same appliance or manufacturer before replacing parts.