Electrolux · Dishwasher · Fault guide

Electrolux Dishwasher i20 error

Errori20

i20 is identified by Electrolux support as the dishwasher did not drain completely. Follow the official, model-scoped checks and service boundary below.

Quick answer

What i20 means

Electrolux Dishwasher i20: the dishwasher did not drain completely. This interpretation applies to Electrolux US dishwashers covered by the linked official error-code and alarm guide in United States / English.

Model scope
Electrolux US dishwashers covered by the linked official error-code and alarm guide
Region
United States / English
Verified
✓

Primary evidence: Electrolux US dishwasher error-code and alarm guide.

Open official source ↗
✓
What the code means

the dishwasher did not drain completely

Follow the exact model manual. check the disposer knockout plug, drain hose, filter and sump before one controlled drain test Do not open fixed panels or test live circuits.

Typical symptoms

01i20 is shown on the Electrolux dishwasher display, indicator, or connected app
02The published condition is: the dishwasher did not drain completely
03Water or condensate does not leave through the documented drain path as expected while i20 is active
04The important observation is when i20 appears and whether the exact published action changes that condition

Fault area and what the code does not prove

Separate the manufacturer-defined condition from components that still need exact-model diagnosis.

01Manufacturer-defined fault area — the dishwasher did not drain completely
02i20 does not distinguish an accessible restriction, hose installation, household drain, pump, wiring, or control until the drain path is checked
03Model boundary — apply this interpretation only to Electrolux US dishwashers covered by the linked official error-code and alarm guide

Safe next steps

  1. 1
    Confirm the exact Electrolux Dishwasher i20 model and displayed code before changing settings.
  2. 2
    Complete only the user-accessible checks described in the linked official source.
  3. 3
    Run one controlled test after the check; if the code returns, stop and use the model manual or qualified service.

Step-by-step diagnosis

  1. 1
    Photograph the complete i20 display before changing controls or removing power
  2. 2
    Confirm that the full model number is covered by this scope: Electrolux US dishwashers covered by the linked official error-code and alarm guide
  3. 3
    Confirm that the observed condition matches the published meaning: the dishwasher did not drain completely
  4. 4
    Published check — check the disposer knockout plug, drain hose, filter and sump before one controlled drain test
  5. 5
    Use the result as the decision point: if the documented condition is corrected, complete only the source-listed check
  6. 6
    if i20 remains, stop and move to exact-model diagnosis
  7. 7
    Published check — If i20 returns after the listed action, do not repeat the same correction indefinitely
  8. 8
    Published check — continue with exact-model diagnosis
  9. 9
    Use the result as the decision point: if the documented condition is corrected, complete only the source-listed check; if i20 remains, stop and move to exact-model diagnosis

Evidence-backed actions

  1. 1
    check the disposer knockout plug, drain hose, filter and sump before one controlled drain test
  2. 2
    If i20 returns after the listed action, do not repeat the same correction indefinitely
  3. 3
    continue with exact-model diagnosis
  4. 4
    If i20 returns after the listed action, do not repeat the same correction indefinitely; continue with exact-model diagnosis

Repair planning

€Cost for the first check
i20 cost planning: €0 for an accessible blockage check; typically €10–€45 for a confirmed hose, cap, or seal. A diagnosed pump repair commonly moves into the €90–€220 service range before parts.
⏱Time for the first check
i20 time plan: 15–35 minutes to drain safely, inspect accessible points, refit them, and run one short drain test.
🔧Tools
Dry towels, shallow tray, and household gloves, Flashlight, A coin or hand grip only if the exact-model manual permits opening the user-accessible filter cover
▣Parts or consumables
i20 parts decision: Usually none for clearing an accessible filter or hose. A drain pump is not confirmed by i20; match any pump, cover, seal, or hose to the full model only after diagnosis.

What not to do

  • Do not force a jammed pump cover, tip an appliance containing water, or reach into the pump area while power is connected
  • Do not turn i20 into a parts diagnosis
  • the display identifies a condition, not a completed component test
  • Do not turn i20 into a parts diagnosis; the display identifies a condition, not a completed component test

Preventive maintenance

  • 1
    Keep user-accessible filters, seals, hoses, and drain connections clean and inspect them periodically for damage or seepage
  • 2
    If i20 begins recurring despite the documented maintenance, stop repeating the same action and request exact-model diagnosis

Frequently asked questions

What exactly does i20 identify?

Electrolux identifies it as the dishwasher did not drain completely.

Which action is actually supported for i20?

check the disposer knockout plug, drain hose, filter and sump before one controlled drain test; If i20 returns after the listed action, do not repeat the same correction indefinitely; continue with exact-model diagnosis.

What result matters after the i20 check?

Whether the documented condition clears after the listed action. If it remains or returns, the exact model needs further diagnosis.

Does i20 prove which part failed?

No. It identifies “the dishwasher did not drain completely”; parts are selected only after the exact model and failed function are confirmed.

What information should accompany a service request?

The i20 photo, full model and serial number, the operating stage when it appeared, and the result of each published check.

Related faults

Compare related codes for the same appliance or manufacturer before replacing parts.