Gorenje · Dishwasher · Fault guide

Gorenje dishwasher F11 error

ErrorF11

Gorenje uses F11 for a water-outlet fault. Check the accessible filters, pump area, and visible drain path with power isolated before service.

Quick answer

What F11 means

Gorenje Dishwasher F11: The dishwasher cannot discharge water correctly. This interpretation applies to Gorenje dishwasher model GV693C60UVAD covered by official manual 875524en in Europe / English manual.

Model scope
Gorenje dishwasher model GV693C60UVAD covered by official manual 875524en
Region
Europe / English manual
Verified
✓

Primary evidence: Gorenje official dishwasher manual 875524en.

Open official source ↗
✓
What the code means

The dishwasher cannot discharge water correctly

Unplug the dishwasher before removing filters or reaching into the pump area. Scoop out water carefully and wear gloves for sharp debris.

Typical symptoms

01F11 appears during draining
02Water remains in the dishwasher tub
03The cycle stops before the drain stage completes

Likely causes

Start with the least invasive explanation and stop if the check requires internal electrical or sealed-system access.

01A blocked coarse or fine filter
02A drain-pump or pump-cover obstruction
03A kinked or restricted drain hose or sink connection

Safe next steps

  1. 1
    Confirm the exact Gorenje Dishwasher F11 model and displayed code before changing settings.
  2. 2
    Complete only the user-accessible checks described in the linked official source.
  3. 3
    Run one controlled test after the check; if the code returns, stop and use the model manual or qualified service.

Step-by-step diagnosis

  1. 1
    Photograph the complete F11 display before changing controls or removing power
  2. 2
    Confirm that the full model number is covered by this scope: Gorenje dishwasher model GV693C60UVAD covered by official manual 875524en
  3. 3
    Confirm that the observed condition matches the published meaning: The dishwasher cannot discharge water correctly
  4. 4
    Confirm F11 and isolate dishwasher power
  5. 5
    Close the water tap before moving or disconnecting any hose
  6. 6
    Remove and clean the coarse and fine filters
  7. 7
    Inspect the pump cover and impeller, then check the visible drain hose and sink connection
  8. 8
    Refit all parts and run one drain test
  9. 9
    contact service if F11 persists
  10. 10
    Published check — Clear only accessible filter, pump-cover, hose, or sink restrictions described by the Gorenje manual

Evidence-backed actions

  1. 1
    Clear only accessible filter, pump-cover, hose, or sink restrictions described by the Gorenje manual
  2. 2
    A clear drain path with recurring F11 needs qualified diagnosis rather than a pump order
  3. 3
    If F11 returns after the listed action, do not repeat the same correction indefinitely; continue with exact-model diagnosis

Repair planning

€Cost for the first check
F11 cost planning: €0 for an accessible blockage check; typically €10–€45 for a confirmed hose, cap, or seal. A diagnosed pump repair commonly moves into the €90–€220 service range before parts.
⏱Time for the first check
F11 time plan: 15–35 minutes to drain safely, inspect accessible points, refit them, and run one short drain test.
🔧Tools
Dry towels, shallow tray, and household gloves, Flashlight, A coin or hand grip only if the exact-model manual permits opening the user-accessible filter cover
▣Parts or consumables
F11 parts decision: Usually none for clearing an accessible filter or hose. A drain pump is not confirmed by F11; match any pump, cover, seal, or hose to the full model only after diagnosis.

What not to do

  • Do not force a jammed pump cover, tip an appliance containing water, or reach into the pump area while power is connected
  • Do not open the pump with power connected, use sharp tools against the impeller, or dismantle the drain pump
  • Do not turn F11 into a parts diagnosis; the display identifies a condition, not a completed component test

Preventive maintenance

  • 1
    Keep user-accessible filters, seals, hoses, and drain connections clean and inspect them periodically for damage or seepage
  • 2
    Rinse filters regularly and keep the drain hose routed without kinks or crushing
  • 3
    If F11 begins recurring despite the documented maintenance, stop repeating the same action and request exact-model diagnosis

Frequently asked questions

What exactly does F11 identify?

Gorenje identifies it as The dishwasher cannot discharge water correctly.

Which action is actually supported for F11?

Clear only accessible filter, pump-cover, hose, or sink restrictions described by the Gorenje manual; A clear drain path with recurring F11 needs qualified diagnosis rather than a pump order.

What result matters after the F11 check?

Whether the documented condition clears after the listed action. If it remains or returns, the exact model needs further diagnosis.

Does F11 prove which part failed?

No. It identifies “The dishwasher cannot discharge water correctly”; parts are selected only after the exact model and failed function are confirmed.

What information should accompany a service request?

The F11 photo, full model and serial number, the operating stage when it appeared, and the result of each published check.

Related faults

Compare related codes for the same appliance or manufacturer before replacing parts.