Gorenje · Dishwasher · Fault guide

Gorenje dishwasher F12 error

ErrorF12

Gorenje identifies F12 as a water-inlet fault. Check the tap and external inlet-hose filter only after closing water and isolating power.

Quick answer

What F12 means

Gorenje Dishwasher F12: The dishwasher is not receiving water correctly. This interpretation applies to Gorenje dishwasher model GV693C60UVAD covered by official manual 875524en in Europe / English manual.

Model scope
Gorenje dishwasher model GV693C60UVAD covered by official manual 875524en
Region
Europe / English manual
Verified
✓

Primary evidence: Gorenje official dishwasher manual 875524en.

Open official source ↗
✓
What the code means

The dishwasher is not receiving water correctly

Close the water tap and unplug the dishwasher before unscrewing the inlet hose or cleaning its external filter. Check every reconnection for leaks.

Typical symptoms

01F12 appears during filling
02The dishwasher does not receive enough water to continue
03The programme stops soon after starting

Likely causes

Start with the least invasive explanation and stop if the check requires internal electrical or sealed-system access.

01The water tap is closed or supply is interrupted
02The external inlet-hose filter is blocked
03A kinked inlet hose or internal inlet fault

Safe next steps

  1. 1
    Confirm the exact Gorenje Dishwasher F12 model and displayed code before changing settings.
  2. 2
    Complete only the user-accessible checks described in the linked official source.
  3. 3
    Run one controlled test after the check; if the code returns, stop and use the model manual or qualified service.

Step-by-step diagnosis

  1. 1
    Photograph the complete F12 display before changing controls or removing power
  2. 2
    Confirm that the full model number is covered by this scope: Gorenje dishwasher model GV693C60UVAD covered by official manual 875524en
  3. 3
    Confirm that the observed condition matches the published meaning: The dishwasher is not receiving water correctly
  4. 4
    Confirm F12 and record the exact model
  5. 5
    Turn off the water tap and unplug the dishwasher
  6. 6
    Check the household tap and visible inlet hose for a kink or leak
  7. 7
    Unscrew the inlet hose only with the tap closed and clean its external filter as the manual shows
  8. 8
    Reconnect, reopen the tap, check for leaks, and test once
  9. 9
    Published check — Correct a closed tap or visible hose restriction and clean the external inlet filter
  10. 10
    Published check — If F12 returns with a good supply, use service rather than selecting an inlet valve from the code alone

Evidence-backed actions

  1. 1
    Correct a closed tap or visible hose restriction and clean the external inlet filter
  2. 2
    If F12 returns with a good supply, use service rather than selecting an inlet valve from the code alone
  3. 3
    If F12 returns after the listed action, do not repeat the same correction indefinitely; continue with exact-model diagnosis

Repair planning

€Cost for the first check
F12 cost planning: €0 to open valves, straighten hoses, or clean an accessible screen; typically €15–€60 for a confirmed replacement inlet hose. If F12 returns with normal supply, €90–€220 is a typical Europe planning range for diagnosis before parts; it is not Gorenje pricing.
⏱Time for the first check
F12 time plan: 10–25 minutes for supply, hose, and accessible-screen checks plus one short fill test.
🔧Tools
Dry towels and a shallow tray, Soft brush for a user-accessible inlet screen only, Hand access to the household water valves
▣Parts or consumables
F12 parts decision: Usually none for the first check. Replace an inlet hose only if it is visibly damaged and the exact Gorenje model specification confirms the correct hose.

What not to do

  • Close the water valves before disconnecting a hose
  • Do not probe the inlet valve electrically or run repeated fill tests if a connection leaks
  • Do not remove a pressurised hose, force the filter, work on live wiring, or run the dishwasher with a leaking connection
  • Do not turn F12 into a parts diagnosis; the display identifies a condition, not a completed component test

Preventive maintenance

  • 1
    Keep inlet hoses unkinked, close household valves before hose work, and clean only user-accessible inlet screens at the exact-model interval
  • 2
    Keep the inlet filter clean and leave the water shut-off accessible for emergencies
  • 3
    If F12 begins recurring despite the documented maintenance, stop repeating the same action and request exact-model diagnosis

Frequently asked questions

What exactly does F12 identify?

Gorenje identifies it as The dishwasher is not receiving water correctly.

Which action is actually supported for F12?

Correct a closed tap or visible hose restriction and clean the external inlet filter; If F12 returns with a good supply, use service rather than selecting an inlet valve from the code alone.

What result matters after the F12 check?

Whether the documented condition clears after the listed action. If it remains or returns, the exact model needs further diagnosis.

Does F12 prove which part failed?

No. It identifies “The dishwasher is not receiving water correctly”; parts are selected only after the exact model and failed function are confirmed.

What information should accompany a service request?

The F12 photo, full model and serial number, the operating stage when it appeared, and the result of each published check.

Related faults

Compare related codes for the same appliance or manufacturer before replacing parts.