Gorenje · Dryer · Fault guide

Gorenje Dryer E01 error

ErrorE01

E01 is identified by Gorenje support as a tumble-dryer temperature-sensor failure. Follow the official, model-scoped checks and service boundary below.

Quick answer

What E01 means

Gorenje Dryer E01: a tumble-dryer temperature-sensor failure. This interpretation applies to Gorenje tumble-dryer models covered by official manual 923904en in Europe / English manual.

Model scope
Gorenje tumble-dryer models covered by official manual 923904en
Region
Europe / English manual
Verified
✓

Primary evidence: Gorenje official tumble-dryer manual 923904en.

Open official source ↗
✓
What the code means

a tumble-dryer temperature-sensor failure

Isolate the appliance when safe. Stop the dryer and contact an authorised Gorenje service centre; do not open or test the sensor circuit. Do not open fixed panels or test live circuits.

Typical symptoms

01E01 is shown on the Gorenje dryer display, indicator, or connected app
02The published condition is: a tumble-dryer temperature-sensor failure
03The control cannot confirm the documented measured condition or sensor reference represented by E01
04The important observation is when E01 appears and whether the exact published action changes that condition

Fault area and what the code does not prove

Separate the manufacturer-defined condition from components that still need exact-model diagnosis.

01Manufacturer-defined fault area — a tumble-dryer temperature-sensor failure
02E01 identifies a measured-condition or sensor path, not a completed proof that the sensor itself failed
03Model boundary — apply this interpretation only to Gorenje tumble-dryer models covered by official manual 923904en

Safe next steps

  1. 1
    Confirm the exact Gorenje Dryer E01 model and displayed code before taking action.
  2. 2
    Keep the appliance in a safe state and use only the external checks named in the official source.
  3. 3
    If the condition remains, stop and arrange qualified service; do not open panels or bypass a safety device.

Step-by-step diagnosis

  1. 1
    Photograph the complete E01 display before changing controls or removing power
  2. 2
    Confirm that the full model number is covered by this scope: Gorenje tumble-dryer models covered by official manual 923904en
  3. 3
    Confirm that the observed condition matches the published meaning: a tumble-dryer temperature-sensor failure
  4. 4
    Published check — Stop the dryer and contact an authorised Gorenje service centre
  5. 5
    Published check — do not open or test the sensor circuit
  6. 6
    Stop at the published service boundary after these actions
  7. 7
    do not add a restart or test cycle that Gorenje does not specify for E01
  8. 8
    Published check — Give service the E01 photo, full model and serial number, when it appeared, and the result of every published external check
  9. 9
    Stop at the published service boundary after these actions; do not add a restart or test cycle that Gorenje does not specify for E01

Service-safe actions

  1. 1
    Stop the dryer and contact an authorised Gorenje service centre
  2. 2
    do not open or test the sensor circuit
  3. 3
    Give service the E01 photo, full model and serial number, when it appeared, and the result of every published external check

Repair planning

€Cost for the first check
E01 cost planning: The source-listed external check costs €0. A qualified sensor-system diagnosis is generally planned within €90–€220 before any model-specific part is approved.
⏱Time for the first check
E01 time plan: 10–20 minutes for the documented E01 external check; allow 30–90 minutes for measured sensor, wiring, and control diagnosis.
🔧Tools
Photo of the complete E01 display, Full model and serial number, The exact-model manual for the published external check, No live sensor-circuit test equipment
▣Parts or consumables
E01 parts decision: E01 describes a tumble-dryer temperature-sensor failure; it does not prove the sensor itself has failed. A blocked path, connector, wiring, control input, or the measured condition can produce the same reported area.

What not to do

  • Do not bridge, heat, cool, wet, or electrically probe a sensor to clear E01
  • Do not replace a sensor until its circuit and the condition it measures have been checked
  • Do not run an extra test cycle after the source tells you to stop or arrange service for E01

Preventive maintenance

  • 1
    Follow the exact Gorenje maintenance schedule for the dryer and keep the model, serial number, and service history available
  • 2
    If E01 begins recurring despite the documented maintenance, stop repeating the same action and request exact-model diagnosis

Frequently asked questions

What exactly does E01 identify?

Gorenje identifies it as a tumble-dryer temperature-sensor failure.

Which action is actually supported for E01?

Stop the dryer and contact an authorised Gorenje service centre; do not open or test the sensor circuit; Give service the E01 photo, full model and serial number, when it appeared, and the result of every published external check.

Can I run another test after E01?

Not unless the official procedure above explicitly includes it. Complete the safe external actions, then keep the appliance stopped at the service boundary.

Does E01 prove which part failed?

No. It identifies “a tumble-dryer temperature-sensor failure”; parts are selected only after the exact model and failed function are confirmed.

What information should accompany a service request?

The E01 photo, full model and serial number, the operating stage when it appeared, and the result of each published check.

Related faults

Compare related codes for the same appliance or manufacturer before replacing parts.