Gorenje · Dryer · Fault guide

Gorenje tumble dryer E00 error

ErrorE00

Gorenje identifies E00 as a control-unit failure. Record the exact model and use qualified service; no control-board replacement is inferred.

Quick answer

What E00 means

Gorenje Dryer E00: The dryer control unit has reported a failure. This interpretation applies to Gorenje tumble-dryer models covered by official manual 964250en in Europe / English manual.

Model scope
Gorenje tumble-dryer models covered by official manual 964250en
Region
Europe / English manual
Verified
✓

Primary evidence: Gorenje official tumble-dryer manual 964250en.

Open official source ↗
✓
What the code means

The dryer control unit has reported a failure

Stop using the dryer and isolate power if it behaves abnormally. Do not remove covers, probe live circuits, or replace the control unit from E00 alone.

Typical symptoms

01E00 appears on the dryer display
02The programme may not start or may stop unexpectedly
03The code returns after the appliance is powered again

Likely causes

Start with the least invasive explanation and stop if the check requires internal electrical or sealed-system access.

01A control-unit fault
02Power or communication damage affecting the control system
03A model-specific electronic failure

Safe next steps

  1. 1
    Confirm the exact Gorenje Dryer E00 model and displayed code before taking action.
  2. 2
    Keep the appliance in a safe state and use only the external checks named in the official source.
  3. 3
    If the condition remains, stop and arrange qualified service; do not open panels or bypass a safety device.

Step-by-step diagnosis

  1. 1
    Photograph the complete E00 display before changing controls or removing power
  2. 2
    Confirm that the full model number is covered by this scope: Gorenje tumble-dryer models covered by official manual 964250en
  3. 3
    Confirm that the observed condition matches the published meaning: The dryer control unit has reported a failure
  4. 4
    Confirm E00 and record the exact model and serial number
  5. 5
    Stop the programme and disconnect power if the dryer behaves abnormally
  6. 6
    Do not open the control area or test live circuits
  7. 7
    Note whether the display, buttons, or programme control also malfunction
  8. 8
    Arrange qualified Gorenje service with the complete code
  9. 9
    Published check — Gorenje identifies E00 as a control-unit failure
  10. 10
    Published check — There is no verified model-independent user repair

Service-safe actions

  1. 1
    Gorenje identifies E00 as a control-unit failure
  2. 2
    There is no verified model-independent user repair
  3. 3
    keep the dryer isolated and let service identify the control, wiring, or supply fault
  4. 4
    Give service the E00 photo, full model and serial number, when it appeared, and the result of every published external check

Repair planning

€Cost for the first check
E00 cost planning: The source-listed safety check is usually €0. €90–€220 is a typical Europe planning range for diagnosis before parts; it is not Gorenje pricing. Ask for separate diagnosis, parts, labor, and call-out lines on the quote.
⏱Time for the first check
E00 time plan: 5–10 minutes to document and isolate safely; 30–90 minutes is a typical diagnostic visit before any model-specific repair.
🔧Tools
Phone camera for the complete E00 display, Full model and serial number, Power or water isolation access as described by the official procedure
▣Parts or consumables
E00 parts decision: No component should be ordered from E00 alone. The documented fault area is “The dryer control unit has reported a failure”; the technician must identify the failed model-specific part and revision.

What not to do

  • Do not open fixed panels, test live circuits, bypass protection, or keep operating the appliance after an urgent stop instruction
  • Do not remove fixed panels, bypass controls, install a generic control board, or continue heated operation with E00 displayed
  • Do not run an extra test cycle after the source tells you to stop or arrange service for E00

Preventive maintenance

  • 1
    Follow the exact Gorenje maintenance schedule for the dryer and keep the model, serial number, and service history available
  • 2
    Keep the dryer dry and ventilated and retain the exact model number for any control-system service
  • 3
    If E00 begins recurring despite the documented maintenance, stop repeating the same action and request exact-model diagnosis

Frequently asked questions

What exactly does E00 identify?

Gorenje identifies it as The dryer control unit has reported a failure.

Which action is actually supported for E00?

Gorenje identifies E00 as a control-unit failure; There is no verified model-independent user repair; keep the dryer isolated and let service identify the control, wiring, or supply fault.

Can I run another test after E00?

Not unless the official procedure above explicitly includes it. Complete the safe external actions, then keep the appliance stopped at the service boundary.

Does E00 prove which part failed?

No. It identifies “The dryer control unit has reported a failure”; parts are selected only after the exact model and failed function are confirmed.

What information should accompany a service request?

The E00 photo, full model and serial number, the operating stage when it appeared, and the result of each published check.

Related faults

Compare related codes for the same appliance or manufacturer before replacing parts.