Gorenje · Dryer · Fault guide

Gorenje tumble dryer PF warning

ErrorPF

Gorenje uses PF for a power-supply failure warning. Resume once with Start/Pause, then investigate the household supply if PF returns.

Quick answer

What PF means

Gorenje Dryer PF: The drying cycle was interrupted by a power failure. This interpretation applies to Gorenje tumble-dryer models covered by official manual 964250en in Europe / English manual.

Model scope
Gorenje tumble-dryer models covered by official manual 964250en
Region
Europe / English manual
Verified
✓

Primary evidence: Gorenje official tumble-dryer manual 964250en.

Open official source ↗
✓
What the code means

The drying cycle was interrupted by a power failure

Do not inspect live wiring or continue if there is a burning smell, heat damage, arcing, or a tripped protective device. Use a qualified electrician or appliance service for recurring supply faults.

Typical symptoms

01PF appears after the dryer loses power
02The drying programme is interrupted
03The cycle may resume when Start/Pause is pressed

Likely causes

Start with the least invasive explanation and stop if the check requires internal electrical or sealed-system access.

01A household power interruption
02A loose or overloaded supply connection
03An intermittent supply fault outside the dryer

Safe next steps

  1. 1
    Confirm the exact Gorenje Dryer PF model and displayed code before changing settings.
  2. 2
    Complete only the user-accessible checks described in the linked official source.
  3. 3
    Run one controlled test after the check; if the code returns, stop and use the model manual or qualified service.

Step-by-step diagnosis

  1. 1
    Photograph the complete PF display before changing controls or removing power
  2. 2
    Confirm that the full model number is covered by this scope: Gorenje tumble-dryer models covered by official manual 964250en
  3. 3
    Confirm that the observed condition matches the published meaning: The drying cycle was interrupted by a power failure
  4. 4
    Confirm PF and record the exact dryer model
  5. 5
    Check whether the household power was interrupted and whether other appliances lost power
  6. 6
    Wait until the dryer is safe to operate, then press Start/Pause once as Gorenje directs
  7. 7
    Observe one controlled resume and stop if there is heat damage, smell, arcing, or another trip
  8. 8
    Arrange qualified electrical or appliance service if PF returns without a known supply interruption
  9. 9
    Published check — Resume the interrupted cycle once with Start/Pause
  10. 10
    Published check — If the warning recurs, have the household supply and dryer connection checked

Evidence-backed actions

  1. 1
    Resume the interrupted cycle once with Start/Pause
  2. 2
    If the warning recurs, have the household supply and dryer connection checked
  3. 3
    PF alone does not justify opening the dryer or replacing a part
  4. 4
    No component repair is indicated while PF remains the documented status “The drying cycle was interrupted by a power failure”

Repair planning

€Cost for the first check
PF cost planning: €0 for the control or setting correction. If the controls remain unresponsive afterward, €90–€220 is a typical Europe planning range for diagnosis before parts; it is not Gorenje pricing.
⏱Time for the first check
PF time plan: 1–5 minutes for the control sequence and one response check.
🔧Tools
No tools required, Use the exact-model control labels shown in the official instructions
▣Parts or consumables
PF parts decision: None for the published PF control procedure.

What not to do

  • Do not force a key, pry up the control panel, or repeat the key sequence rapidly if the display does not respond
  • Do not repeatedly restart after a burning smell or tripped protection, use an extension lead that is not rated for the dryer, or inspect live wiring
  • Do not order a part or interrupt normal operation solely because PF is displayed

Preventive maintenance

  • 1
    Learn the model's normal indicators and control-lock sequence so a status message is not mistaken for a hardware fault
  • 2
    Keep the dryer's dedicated supply and socket accessible and never ignore heat marks, a burning smell, or repeated protective-device trips
  • 3
    Record a change in behavior rather than treating the normal PF state itself as a maintenance fault

Frequently asked questions

What exactly does PF identify?

Gorenje identifies it as The drying cycle was interrupted by a power failure.

Which action is actually supported for PF?

Resume the interrupted cycle once with Start/Pause; If the warning recurs, have the household supply and dryer connection checked; PF alone does not justify opening the dryer or replacing a part.

What result matters after the PF check?

Whether the documented condition clears after the listed action. If it remains or returns, the exact model needs further diagnosis.

Does PF prove which part failed?

No. It identifies “The drying cycle was interrupted by a power failure”; parts are selected only after the exact model and failed function are confirmed.

What information should accompany a service request?

The PF photo, full model and serial number, the operating stage when it appeared, and the result of each published check.

Related faults

Compare related codes for the same appliance or manufacturer before replacing parts.