Samsung · Dishwasher · Fault guide

Samsung dishwasher 9E error

Error9E

Samsung identifies 9E as a low-water-level error. Empty the dishwasher, add detergent, run one Normal cycle, and request service if it returns.

Quick answer

What 9E means

Samsung Dishwasher 9E: The dishwasher has detected too little water. This interpretation applies to Samsung US dishwasher models covered by the linked official error-code guidance in United States / English.

Model scope
Samsung US dishwasher models covered by the linked official error-code guidance
Region
United States / English
Verified
✓

Primary evidence: Samsung US dishwasher error-code support.

Open official source ↗
✓
What the code means

The dishwasher has detected too little water

Do not open panels or work on the inlet system. Close the water supply if a visible leak appears and stop using the appliance until it is safe.

Typical symptoms

019E appears during a cycle
02The dishwasher may stop or wash poorly
03The code returns after a Normal cycle

Likely causes

Start with the least invasive explanation and stop if the check requires internal electrical or sealed-system access.

01Insufficient water reached the dishwasher
02A water-supply restriction or internal fill fault
03A model-specific low-level condition

Safe next steps

  1. 1
    Confirm the exact Samsung Dishwasher 9E model and displayed code before taking action.
  2. 2
    Keep the appliance in a safe state and use only the external checks named in the official source.
  3. 3
    If the condition remains, stop and arrange qualified service; do not open panels or bypass a safety device.

Step-by-step diagnosis

  1. 1
    Photograph the complete 9E display before changing controls or removing power
  2. 2
    Confirm that the full model number is covered by this scope: Samsung US dishwasher models covered by the linked official error-code guidance
  3. 3
    Confirm that the observed condition matches the published meaning: The dishwasher has detected too little water
  4. 4
    Confirm the code is 9E and record the exact model
  5. 5
    Empty the dishwasher
  6. 6
    Add the detergent specified for the model and run one Normal cycle
  7. 7
    Watch for leaks or abnormal filling and stop if either occurs
  8. 8
    If 9E returns, switch off power at the circuit breaker and request Samsung service
  9. 9
    Published check — Samsung's published user procedure for 9E is the empty, detergent, Normal-cycle test
  10. 10
    Published check — Do not open the inlet system or choose a valve, sensor, or control part from 9E alone

Service-safe actions

  1. 1
    Samsung's published user procedure for 9E is the empty, detergent, Normal-cycle test
  2. 2
    Do not open the inlet system or choose a valve, sensor, or control part from 9E alone
  3. 3
    arrange service if the test fails
  4. 4
    Give service the 9E photo, full model and serial number, when it appeared, and the result of every published external check

Repair planning

€Cost for the first check
9E cost planning: €0 to open valves, straighten hoses, or clean an accessible screen; typically €15–€60 for a confirmed replacement inlet hose. If 9E returns with normal supply, €90–€220 is a typical Europe planning range for diagnosis before parts; it is not Samsung pricing.
⏱Time for the first check
9E time plan: 10–25 minutes for supply, hose, and accessible-screen checks plus one short fill test.
🔧Tools
Dry towels and a shallow tray, Soft brush for a user-accessible inlet screen only, Hand access to the household water valves
▣Parts or consumables
9E parts decision: Usually none for the first check. Replace an inlet hose only if it is visibly damaged and the exact Samsung model specification confirms the correct hose.

What not to do

  • Close the water valves before disconnecting a hose
  • Do not probe the inlet valve electrically or run repeated fill tests if a connection leaks
  • Do not continue cycles with a leak, bypass the water-level system, or open fixed panels
  • Do not run an extra test cycle after the source tells you to stop or arrange service for 9E

Preventive maintenance

  • 1
    Keep inlet hoses unkinked, close household valves before hose work, and clean only user-accessible inlet screens at the exact-model interval
  • 2
    Keep the supply shut-off accessible and maintain the water line according to the installation manual
  • 3
    If 9E begins recurring despite the documented maintenance, stop repeating the same action and request exact-model diagnosis

Frequently asked questions

What exactly does 9E identify?

Samsung identifies it as The dishwasher has detected too little water.

Which action is actually supported for 9E?

Samsung's published user procedure for 9E is the empty, detergent, Normal-cycle test; Do not open the inlet system or choose a valve, sensor, or control part from 9E alone; arrange service if the test fails.

Can I run another test after 9E?

Not unless the official procedure above explicitly includes it. Complete the safe external actions, then keep the appliance stopped at the service boundary.

Does 9E prove which part failed?

No. It identifies “The dishwasher has detected too little water”; parts are selected only after the exact model and failed function are confirmed.

What information should accompany a service request?

The 9E photo, full model and serial number, the operating stage when it appeared, and the result of each published check.

Related faults

Compare related codes for the same appliance or manufacturer before replacing parts.