Samsung · Dishwasher · Fault guide

Samsung dishwasher OC / 0C / oE error

ErrorOC / 0C / oE

Samsung identifies OC, 0C, and oE as over-level water errors. Use the official drain and overflow checks, then stop if water remains or the code returns.

Quick answer

What OC / 0C / oE means

Samsung Dishwasher OC / 0C / oE: There is more water in the dishwasher than there should be. This interpretation applies to Samsung US dishwasher models covered by the linked official drain and error-code guidance in United States / English.

Model scope
Samsung US dishwasher models covered by the linked official drain and error-code guidance
Region
United States / English
Verified
✓

Primary evidence: Samsung US dishwasher drain and overflow support.

Open official source ↗
✓
What the code means

There is more water in the dishwasher than there should be

If water is actively leaking, close the water shut-off and isolate power. Wear protection against sharp debris and do not open internal panels.

Typical symptoms

01OC, 0C, or oE appears during or after a cycle
02Water remains in the tub or the dishwasher tries to drain
03The sink drain, hose, filter area, or overflow path may be restricted

Likely causes

Start with the least invasive explanation and stop if the check requires internal electrical or sealed-system access.

01A blocked sink drain or disposal
02A pinched or incorrectly routed drain hose
03Food or debris in the accessible drain area
04A fill or overflow fault requiring service

Safe next steps

  1. 1
    Confirm the exact Samsung Dishwasher OC / 0C / oE model and displayed code before changing settings.
  2. 2
    Complete only the user-accessible checks described in the linked official source.
  3. 3
    Run one controlled test after the check; if the code returns, stop and use the model manual or qualified service.

Step-by-step diagnosis

  1. 1
    Photograph the complete OC / 0C / oE display before changing controls or removing power
  2. 2
    Confirm that the full model number is covered by this scope: Samsung US dishwasher models covered by the linked official drain and error-code guidance
  3. 3
    Confirm that the observed condition matches the published meaning: There is more water in the dishwasher than there should be
  4. 4
    If water is leaking, close the water shut-off and isolate power
  5. 5
    Check the sink drain and garbage disposal for blockage
  6. 6
    Inspect drain-hose routing for pinching, kinks, and the required high loop or air gap
  7. 7
    Clean the accessible filter and drain area as the exact manual permits
  8. 8
    Run one drain test and request service if OC/0C/oE or standing water returns
  9. 9
    Published check — Clear only visible sink, disposal, hose, or filter restrictions and reassemble the drain area correctly
  10. 10
    Published check — Samsung's linked guidance does not verify an internal overflow repair

Evidence-backed actions

  1. 1
    Clear only visible sink, disposal, hose, or filter restrictions and reassemble the drain area correctly
  2. 2
    Samsung's linked guidance does not verify an internal overflow repair
  3. 3
    use service when the code or water level returns
  4. 4
    If OC / 0C / oE returns after the listed action, do not repeat the same correction indefinitely; continue with exact-model diagnosis

Repair planning

€Cost for the first check
OC / 0C / oE cost planning: €0 for a safe external inspection; typically €15–€80 for a confirmed external hose or seal. Internal leak diagnosis is commonly €90–€220 before parts.
⏱Time for the first check
OC / 0C / oE time plan: 5–15 minutes to shut off water and inspect externally; allow 30–90 minutes for professional leak tracing.
🔧Tools
Dry towels and a shallow tray, Flashlight for external connections, Access to the water shut-off
▣Parts or consumables
OC / 0C / oE parts decision: No part can be selected until the leak location is found. A visibly damaged external hose or seal must match the full Samsung model and connection type.

What not to do

  • Do not run another cycle to reproduce an active leak, tilt the appliance, bypass a float switch, or energize wet electrical areas
  • Do not run the dishwasher while it leaks, reach into the drain with power connected, or bypass the water-level or overflow protection
  • Do not turn OC / 0C / oE into a parts diagnosis; the display identifies a condition, not a completed component test

Preventive maintenance

  • 1
    Keep user-accessible filters, seals, hoses, and drain connections clean and inspect them periodically for damage or seepage
  • 2
    Keep the sink connection, drain hose, filter, and locally required high loop or air gap maintained
  • 3
    If OC / 0C / oE begins recurring despite the documented maintenance, stop repeating the same action and request exact-model diagnosis

Frequently asked questions

What exactly does OC / 0C / oE identify?

Samsung identifies it as There is more water in the dishwasher than there should be.

Which action is actually supported for OC / 0C / oE?

Clear only visible sink, disposal, hose, or filter restrictions and reassemble the drain area correctly; Samsung's linked guidance does not verify an internal overflow repair; use service when the code or water level returns.

What result matters after the OC / 0C / oE check?

Whether the documented condition clears after the listed action. If it remains or returns, the exact model needs further diagnosis.

Does OC / 0C / oE prove which part failed?

No. It identifies “There is more water in the dishwasher than there should be”; parts are selected only after the exact model and failed function are confirmed.

What information should accompany a service request?

The OC / 0C / oE photo, full model and serial number, the operating stage when it appeared, and the result of each published check.

Related faults

Compare related codes for the same appliance or manufacturer before replacing parts.