Dryer error codes and fault guides
Browse 81 published, evidence-gated Dryer guides. Each page states the supported model and region, official source, safe checks, and the point to stop.
Dryer fault guides
49–72 of 81
the Smart Washer/Dryer is waiting for WiFi setup
WiFi LED flashing is identified by GE Appliances' official support as the Smart Washer/Dryer is waiting for WiFi setup. Follow the model-scoped checks and service boundary below.
the Smart Washer/Dryer has completed WiFi connection
WiFi LED solid is identified by GE Appliances' official support as the Smart Washer/Dryer has completed WiFi connection. Follow the model-scoped checks and service boundary below.
the Smart Laundry appliance is ready for network setup
WiFi setup LED flashing is identified by GE Appliances' official support as the Smart Laundry appliance is ready for network setup. Follow the model-scoped checks and service boundary below.
the Smart Laundry appliance has connected to the home network
WiFi setup LED solid is identified by GE Appliances' official support as the Smart Laundry appliance has connected to the home network. Follow the model-scoped checks and service boundary below.
The dryer control unit has reported a failure
Gorenje identifies E00 as a control-unit failure. Record the exact model and use qualified service; no control-board replacement is inferred.
a tumble-dryer temperature-sensor failure
E01 is identified by Gorenje support as a tumble-dryer temperature-sensor failure. Follow the official, model-scoped checks and service boundary below.
The dryer has detected a communication error
Gorenje identifies E02 as a communication error. Capture the exact code and model, then use qualified service for the internal connection diagnosis.
The condensate pump is not pumping water to the tank normally
Gorenje identifies E03 as a condensate-pump error. Check the user-accessible condensate path and stop if the code persists.
tumble-dryer system overheating
E04 is identified by Gorenje support as tumble-dryer system overheating. Follow the official, model-scoped checks and service boundary below.
The dryer control unit has reported a failure
Gorenje groups E07 and E08 as control-unit failures. Disconnect the dryer from power and arrange qualified service.
The BLDC motor and control unit are not communicating
Gorenje identifies E11 as a BLDC motor communication error. Do not open the motor circuit; arrange service with the exact dryer model.
The dryer cannot connect to the Wi-Fi network for remote control
Gorenje identifies E17 as a Wi-Fi network connection issue affecting remote control, not the dryer’s normal drying programmes.
The dryer has detected a temperature-sensor failure
Gorenje groups E91, E92, and E93 as temperature-sensor failures. Stop using the dryer and arrange service rather than guessing a sensor part.
The drying cycle was interrupted by a power failure
Gorenje uses PF for a power-supply failure warning. Resume once with Start/Pause, then investigate the household supply if PF returns.
drainage-pump failure
F2 is identified by Haier support as drainage-pump failure. Follow the official, model-scoped checks and service boundary below.
an electronic circuit-board fault that can make dryer functions unavailable
F01 is identified in Hotpoint's official United Kingdom appliance-specific table as an electronic circuit-board fault that can make dryer functions unavailable. Use only the published external check or service boundary below.
restricted airflow through the lint screen or vent
AF is identified by Maytag's official support as restricted airflow through the lint screen or vent. Follow the model-scoped checks and safety boundary below.
an E1 dryer fault requiring model-specific diagnosis
E1 is identified by Maytag's official support as an E1 dryer fault requiring model-specific diagnosis. Follow the model-scoped checks and safety boundary below.
an E2 dryer fault requiring model-specific diagnosis
E2 is identified by Maytag's official support as an E2 dryer fault requiring model-specific diagnosis. Follow the model-scoped checks and safety boundary below.
an E3 dryer fault requiring model-specific diagnosis
E3 is identified by Maytag's official support as an E3 dryer fault requiring model-specific diagnosis. Follow the model-scoped checks and safety boundary below.
the door is not fully closed and latched
ERR is identified by Maytag's official support as the door is not fully closed and latched. Follow the model-scoped checks and safety boundary below.
an F01 dryer fault requiring model-specific diagnosis
F01 is identified by Maytag's official support as an F01 dryer fault requiring model-specific diagnosis. Follow the model-scoped checks and safety boundary below.
an F02 dryer fault requiring model-specific diagnosis
F02 is identified by Maytag's official support as an F02 dryer fault requiring model-specific diagnosis. Follow the model-scoped checks and safety boundary below.
a possible heater or heater-relay problem
F4E1 is identified by Maytag's official support as a possible heater or heater-relay problem. Follow the model-scoped checks and safety boundary below.