Electrolux · Dishwasher · Fault guide

Electrolux dishwasher i20 code

Errori20

i20 is described by Electrolux support as dishwasher did not drain properly. Exact checks and component access vary by model and region.

Quick answer

What i20 means

Electrolux Dishwasher i20: Dishwasher did not drain properly. This interpretation applies to Electrolux dishwasher models listed by the linked official code table in US / English.

Model scope
Electrolux dishwasher models listed by the linked official code table
Region
US / English
Verified
✓

Primary evidence: Electrolux US dishwasher and washer error codes.

Open official source ↗
✓
What the code means

Dishwasher did not drain properly

Switch the dishwasher off before cleaning user-accessible parts. Hidden glass may be present near the filter and pump cover.

Typical symptoms

01i20 is shown on the Electrolux dishwasher display, indicator, or connected app
02The published condition is: Dishwasher did not drain properly
03Water or condensate does not leave through the documented drain path as expected while i20 is active
04The important observation is when i20 appears and whether the exact published action changes that condition

Fault area and what the code does not prove

Separate the manufacturer-defined condition from components that still need exact-model diagnosis.

01Manufacturer-defined fault area — Dishwasher did not drain properly
02i20 does not distinguish an accessible restriction, hose installation, household drain, pump, wiring, or control until the drain path is checked
03Model boundary — apply this interpretation only to Electrolux dishwasher models listed by the linked official code table

Safe next steps

  1. 1
    Confirm the exact Electrolux Dishwasher i20 model and displayed code before changing settings.
  2. 2
    Complete only the user-accessible checks described in the linked official source.
  3. 3
    Run one controlled test after the check; if the code returns, stop and use the model manual or qualified service.

Step-by-step diagnosis

  1. 1
    Photograph the complete i20 display before changing controls or removing power
  2. 2
    Confirm that the full model number is covered by this scope: Electrolux dishwasher models listed by the linked official code table
  3. 3
    Confirm that the observed condition matches the published meaning: Dishwasher did not drain properly
  4. 4
    Stop the dishwasher
  5. 5
    Check that the disposer knockout plug was removed if the drain connects to a disposer
  6. 6
    Check the visible drain hose for blockage, pinching, or restriction
  7. 7
    Confirm the hose is installed at least 32 inches from the floor as Electrolux specifies
  8. 8
    Clean the user-accessible glass trap/filter
  9. 9
    Clear the code using Cancel, the breaker, or a three-minute unplug only as the model manual permits
  10. 10
    Run one controlled test

Evidence-backed actions

  1. 1
    Electrolux identifies i20 as incomplete drainage
  2. 2
    Check the disposer knockout plug, visible drain hose, hose height, and user-accessible glass trap/filter
  3. 3
    After correcting an external restriction, clear the code by the model's permitted Cancel or power-reset method and run one test
  4. 4
    A recurring i20 needs service rather than a drain-pump replacement based on the code alone
  5. 5
    If i20 returns after the listed action, do not repeat the same correction indefinitely; continue with exact-model diagnosis

Repair planning

€Cost for the first check
i20 cost planning: €0 for an accessible blockage check; typically €10–€45 for a confirmed hose, cap, or seal. A diagnosed pump repair commonly moves into the €90–€220 service range before parts.
⏱Time for the first check
i20 time plan: 15–35 minutes to drain safely, inspect accessible points, refit them, and run one short drain test.
🔧Tools
Dry towels, shallow tray, and household gloves, Flashlight, A coin or hand grip only if the exact-model manual permits opening the user-accessible filter cover
▣Parts or consumables
i20 parts decision: Usually none for clearing an accessible filter or hose. A drain pump is not confirmed by i20; match any pump, cover, seal, or hose to the full model only after diagnosis.

What not to do

  • Do not force a jammed pump cover, tip an appliance containing water, or reach into the pump area while power is connected
  • Do not disconnect hoses while the dishwasher contains hot water
  • Do not reach into a disposer or pump area
  • Do not alter the drain route below the manufacturer requirement
  • Do not run repeated cycles if water backs up or leaks
  • Do not turn i20 into a parts diagnosis; the display identifies a condition, not a completed component test

Preventive maintenance

  • 1
    Keep user-accessible filters, seals, hoses, and drain connections clean and inspect them periodically for damage or seepage
  • 2
    Keep the drain hose free from kinks and crushing
  • 3
    Clean the user-accessible glass trap/filter regularly
  • 4
    If i20 begins recurring despite the documented maintenance, stop repeating the same action and request exact-model diagnosis

Frequently asked questions

What exactly does i20 identify?

Electrolux identifies it as Dishwasher did not drain properly.

Which action is actually supported for i20?

Electrolux identifies i20 as incomplete drainage; Check the disposer knockout plug, visible drain hose, hose height, and user-accessible glass trap/filter; After correcting an external restriction, clear the code by the model's permitted Cancel or power-reset method and run one test; A recurring i20 needs service rather than a drain-pump replacement based on the code alone.

What result matters after the i20 check?

Whether the documented condition clears after the listed action. If it remains or returns, the exact model needs further diagnosis.

Does i20 prove which part failed?

No. It identifies “Dishwasher did not drain properly”; parts are selected only after the exact model and failed function are confirmed.

What information should accompany a service request?

The i20 photo, full model and serial number, the operating stage when it appeared, and the result of each published check.

Related faults

Compare related codes for the same appliance or manufacturer before replacing parts.