AEG · Dishwasher · Fault guide

AEG dishwasher i10 / i11 code

Errori10 / i11

i10 / i11 is described by AEG support as water-inlet problem; no water entering. Exact checks and component access vary by model and region.

Quick answer

What i10 / i11 means

AEG Dishwasher i10 / i11: Water-inlet problem; no water entering. This interpretation applies to AEG dishwasher models listed by the linked official code table in UK / English.

Model scope
AEG dishwasher models listed by the linked official code table
Region
UK / English
Verified
✓

Primary evidence: AEG UK dishwasher error codes.

Open official source ↗
✓
What the code means

Water-inlet problem; no water entering

Switch the dishwasher off before cleaning user-accessible parts. Hidden glass may be present near the filter and pump cover.

Typical symptoms

01i10 / i11 is shown on the AEG dishwasher display, indicator, or connected app
02The published condition is: Water-inlet problem; no water entering
03The affected fill stage does not receive or confirm the expected water supply while i10 / i11 is active
04The important observation is when i10 / i11 appears and whether the exact published action changes that condition

Fault area and what the code does not prove

Separate the manufacturer-defined condition from components that still need exact-model diagnosis.

01Manufacturer-defined fault area — Water-inlet problem; no water entering
02i10 / i11 does not distinguish household supply, hose, accessible screen, inlet hardware, wiring, or control until the listed checks are completed
03Model boundary — apply this interpretation only to AEG dishwasher models listed by the linked official code table

Safe next steps

  1. 1
    Confirm the exact AEG Dishwasher i10 / i11 model and displayed code before changing settings.
  2. 2
    Complete only the user-accessible checks described in the linked official source.
  3. 3
    Run one controlled test after the check; if the code returns, stop and use the model manual or qualified service.

Step-by-step diagnosis

  1. 1
    Photograph the complete i10 / i11 display before changing controls or removing power
  2. 2
    Confirm that the full model number is covered by this scope: AEG dishwasher models listed by the linked official code table
  3. 3
    Confirm that the observed condition matches the published meaning: Water-inlet problem; no water entering
  4. 4
    Check that the water tap is fully open
  5. 5
    Check household water flow
  6. 6
    AEG specifies filling a 5-litre bucket in 30 seconds from one tap
  7. 7
    Check the visible inlet hose for a kink, twist, or damage
  8. 8
    With the tap closed, clean the inlet-hose filter only as the model manual shows
  9. 9
    Check accessible dishwasher filters and drain-hose position
  10. 10
    If recently installed or moved, confirm the sink-drain blanking plug was removed

Evidence-backed actions

  1. 1
    AEG identifies i10/i11 as no-water-inlet errors
  2. 2
    Open the water tap, check household flow, and straighten a kinked inlet hose
  3. 3
    With the tap closed, clean the inlet filter only as the exact manual directs
  4. 4
    Check the accessible filters and drain route, then test once
  5. 5
    A damaged hose or a persistent code requires an engineer
  6. 6
    If i10 / i11 returns after the listed action, do not repeat the same correction indefinitely; continue with exact-model diagnosis

Repair planning

€Cost for the first check
i10 / i11 cost planning: €0 to open valves, straighten hoses, or clean an accessible screen; typically €15–€60 for a confirmed replacement inlet hose. If i10 / i11 returns with normal supply, €90–€220 is a typical Europe planning range for diagnosis before parts; it is not AEG pricing.
⏱Time for the first check
i10 / i11 time plan: 10–25 minutes for supply, hose, and accessible-screen checks plus one short fill test.
🔧Tools
Dry towels and a shallow tray, Soft brush for a user-accessible inlet screen only, Hand access to the household water valves
▣Parts or consumables
i10 / i11 parts decision: Usually none for the first check. Replace an inlet hose only if it is visibly damaged and the exact AEG model specification confirms the correct hose.

What not to do

  • Close the water valves before disconnecting a hose
  • Do not probe the inlet valve electrically or run repeated fill tests if a connection leaks
  • Do not use a damaged inlet hose
  • Do not remove the inlet hose while the tap is open
  • Do not remove fixed panels or work on live electrical parts
  • Do not continue if a connection leaks
  • Do not turn i10 / i11 into a parts diagnosis; the display identifies a condition, not a completed component test

Preventive maintenance

  • 1
    Keep inlet hoses unkinked, close household valves before hose work, and clean only user-accessible inlet screens at the exact-model interval
  • 2
    Inspect the visible inlet hose for twists, damage, and leaks
  • 3
    Keep accessible filters clean following the model manual
  • 4
    If i10 / i11 begins recurring despite the documented maintenance, stop repeating the same action and request exact-model diagnosis

Frequently asked questions

What exactly does i10 / i11 identify?

AEG identifies it as Water-inlet problem; no water entering.

Which action is actually supported for i10 / i11?

AEG identifies i10/i11 as no-water-inlet errors; Open the water tap, check household flow, and straighten a kinked inlet hose; With the tap closed, clean the inlet filter only as the exact manual directs; Check the accessible filters and drain route, then test once; A damaged hose or a persistent code requires an engineer.

What result matters after the i10 / i11 check?

Whether the documented condition clears after the listed action. If it remains or returns, the exact model needs further diagnosis.

Does i10 / i11 prove which part failed?

No. It identifies “Water-inlet problem; no water entering”; parts are selected only after the exact model and failed function are confirmed.

What information should accompany a service request?

The i10 / i11 photo, full model and serial number, the operating stage when it appeared, and the result of each published check.

Related faults

Compare related codes for the same appliance or manufacturer before replacing parts.