AEG · Dishwasher · Fault guide

AEG dishwasher i60 / i61 / i69 / i6C code

Errori60 / i61 / i69 / i6C

i60 / i61 / i69 / i6C is described by AEG support as heating or temperature-sensing fault. Exact checks and component access vary by model and region.

Quick answer

What i60 / i61 / i69 / i6C means

AEG Dishwasher i60 / i61 / i69 / i6C: Heating or temperature-sensing fault. This interpretation applies to AEG dishwashers covered by the linked support article in United Kingdom / English.

Model scope
AEG dishwashers covered by the linked support article
Region
United Kingdom / English
Verified
✓

Primary evidence: AEG support: dishwasher i60/i61/i69/i6C.

Open official source ↗
✓
What the code means

Heating or temperature-sensing fault

Do not open fixed panels or test live electrical parts. Record the full model number and arrange qualified service if the code returns after the permitted external checks.

Typical symptoms

01i60 / i61 / i69 / i6C is shown on the AEG dishwasher display, indicator, or connected app
02The published condition is: Heating or temperature-sensing fault
03The measured temperature condition does not match the operating range represented by i60 / i61 / i69 / i6C
04The important observation is when i60 / i61 / i69 / i6C appears and whether the exact published action changes that condition

Fault area and what the code does not prove

Separate the manufacturer-defined condition from components that still need exact-model diagnosis.

01Manufacturer-defined fault area — Heating or temperature-sensing fault
02i60 / i61 / i69 / i6C identifies the temperature condition but does not alone prove a sensor, airflow, heater, refrigerant, wiring, or control fault
03Model boundary — apply this interpretation only to AEG dishwashers covered by the linked support article

Safe next steps

  1. 1
    Confirm the exact AEG Dishwasher i60 / i61 / i69 / i6C model and displayed code before taking action.
  2. 2
    Keep the appliance in a safe state and use only the external checks named in the official source.
  3. 3
    If the condition remains, stop and arrange qualified service; do not open panels or bypass a safety device.

Step-by-step diagnosis

  1. 1
    Photograph the complete i60 / i61 / i69 / i6C display before changing controls or removing power
  2. 2
    Confirm that the full model number is covered by this scope: AEG dishwashers covered by the linked support article
  3. 3
    Confirm that the observed condition matches the published meaning: Heating or temperature-sensing fault
  4. 4
    Check that the incoming water temperature at the connection is not above 60°C
  5. 5
    Unplug the dishwasher
  6. 6
    Check the user-accessible filters and sump for foam, suds, or debris
  7. 7
    Clean the filters and clear accessible foam or suds
  8. 8
    Reconnect power, select a suitable cycle, and test once
  9. 9
    Arrange an AEG-approved service visit if the code returns
  10. 10
    Published check — AEG identifies i60/i61/i69/i6C as heating or temperature-sensing conditions

Service-safe actions

  1. 1
    AEG identifies i60/i61/i69/i6C as heating or temperature-sensing conditions
  2. 2
    Check that inlet water is no hotter than 60°C, then unplug the dishwasher and clean only the accessible filters and sump of foam, suds, and debris
  3. 3
    Reconnect and test one suitable cycle
  4. 4
    If it returns, arrange approved service
  5. 5
    do not replace a heater or sensor from the code alone
  6. 6
    Give service the i60 / i61 / i69 / i6C photo, full model and serial number, when it appeared, and the result of every published external check

Repair planning

€Cost for the first check
i60 / i61 / i69 / i6C cost planning: €0 to open valves, straighten hoses, or clean an accessible screen; typically €15–€60 for a confirmed replacement inlet hose. If i60 / i61 / i69 / i6C returns with normal supply, €90–€220 is a typical Europe planning range for diagnosis before parts; it is not AEG pricing.
⏱Time for the first check
i60 / i61 / i69 / i6C time plan: 10–25 minutes for supply, hose, and accessible-screen checks plus one short fill test.
🔧Tools
Dry towels and a shallow tray, Soft brush for a user-accessible inlet screen only, Hand access to the household water valves
▣Parts or consumables
i60 / i61 / i69 / i6C parts decision: Usually none for the first check. Replace an inlet hose only if it is visibly damaged and the exact AEG model specification confirms the correct hose.

What not to do

  • Close the water valves before disconnecting a hose
  • Do not probe the inlet valve electrically or run repeated fill tests if a connection leaks
  • Do not test heater or sensor wiring
  • Do not use water above 60°C at the inlet connection
  • Do not remove fixed panels
  • Do not continue repeated cycles if the fault returns
  • Do not run an extra test cycle after the source tells you to stop or arrange service for i60 / i61 / i69 / i6C

Preventive maintenance

  • 1
    Keep inlet hoses unkinked, close household valves before hose work, and clean only user-accessible inlet screens at the exact-model interval
  • 2
    Use dishwasher detergent as directed to avoid excess suds
  • 3
    Keep accessible filters clean following the model manual
  • 4
    If i60 / i61 / i69 / i6C begins recurring despite the documented maintenance, stop repeating the same action and request exact-model diagnosis

Frequently asked questions

What exactly does i60 / i61 / i69 / i6C identify?

AEG identifies it as Heating or temperature-sensing fault.

Which action is actually supported for i60 / i61 / i69 / i6C?

AEG identifies i60/i61/i69/i6C as heating or temperature-sensing conditions; Check that inlet water is no hotter than 60°C, then unplug the dishwasher and clean only the accessible filters and sump of foam, suds, and debris; Reconnect and test one suitable cycle; If it returns, arrange approved service; do not replace a heater or sensor from the code alone.

Can I run another test after i60 / i61 / i69 / i6C?

Not unless the official procedure above explicitly includes it. Complete the safe external actions, then keep the appliance stopped at the service boundary.

Does i60 / i61 / i69 / i6C prove which part failed?

No. It identifies “Heating or temperature-sensing fault”; parts are selected only after the exact model and failed function are confirmed.

What information should accompany a service request?

The i60 / i61 / i69 / i6C photo, full model and serial number, the operating stage when it appeared, and the result of each published check.

Related faults

Compare related codes for the same appliance or manufacturer before replacing parts.