Gorenje · Dishwasher · Fault guide

Gorenje dishwasher F10 error

ErrorF10

Gorenje identifies F10 as a dishwasher overfilling condition. The official first check is the accessible drainage pump area; use service if F10 persists.

Quick answer

What F10 means

Gorenje Dishwasher F10: The dishwasher has detected too much water. This interpretation applies to Gorenje dishwasher model GV693C60UVAD covered by official manual 875524en in Europe / English manual.

Model scope
Gorenje dishwasher model GV693C60UVAD covered by official manual 875524en
Region
Europe / English manual
Verified
✓

Primary evidence: Gorenje official dishwasher manual 875524en.

Open official source ↗
!
Stop and make safe

The dishwasher has detected too much water

Turn off the dishwasher and unplug it before checking the pump. Close the water tap if water is entering or leaking; do not run the appliance while it overfills.

Typical symptoms

01F10 appears during a programme
02Water may remain in the tub or collect around the appliance
03The dishwasher may stop to protect against overfilling

Likely causes

Start with the least invasive explanation and stop if the check requires internal electrical or sealed-system access.

01A blocked drainage pump or drain path
02A water-level or inlet fault requiring model-specific diagnosis
03An installation drain restriction

Safe next steps

  1. 1
    Confirm the exact Gorenje Dishwasher F10 model and displayed code before taking action.
  2. 2
    Keep the appliance in a safe state and use only the external checks named in the official source.
  3. 3
    If the condition remains, stop and arrange qualified service; do not open panels or bypass a safety device.

Step-by-step diagnosis

  1. 1
    Photograph the complete F10 display before changing controls or removing power
  2. 2
    Confirm that the full model number is covered by this scope: Gorenje dishwasher model GV693C60UVAD covered by official manual 875524en
  3. 3
    Confirm that the observed condition matches the published meaning: The dishwasher has detected too much water
  4. 4
    Confirm F10 and record GV693C60UVAD or the exact model shown on the rating plate
  5. 5
    Turn off the dishwasher and unplug it
  6. 6
    Remove the filters and scoop standing water as the manual shows
  7. 7
    Inspect the accessible drainage-pump cover and impeller for a foreign object
  8. 8
    Refit the pump cover and filters, then request service if F10 returns
  9. 9
    Published check — Gorenje's F10 procedure is limited to unblocking the accessible drainage-pump area
  10. 10
    Published check — Do not infer an inlet valve or pump replacement from F10

Evidence-backed actions

  1. 1
    Gorenje's F10 procedure is limited to unblocking the accessible drainage-pump area
  2. 2
    Do not infer an inlet valve or pump replacement from F10
  3. 3
    use service when overfilling continues
  4. 4
    Give service the F10 photo, full model and serial number, when it appeared, and the result of every published external check

Repair planning

€Cost for the first check
F10 cost planning: €0 for a safe external inspection; typically €15–€80 for a confirmed external hose or seal. Internal leak diagnosis is commonly €90–€220 before parts.
⏱Time for the first check
F10 time plan: 5–15 minutes to shut off water and inspect externally; allow 30–90 minutes for professional leak tracing.
🔧Tools
Dry towels and a shallow tray, Flashlight for external connections, Access to the water shut-off
▣Parts or consumables
F10 parts decision: No part can be selected until the leak location is found. A visibly damaged external hose or seal must match the full Gorenje model and connection type.

What not to do

  • Do not run another cycle to reproduce an active leak, tilt the appliance, bypass a float switch, or energize wet electrical areas
  • Do not reach into the pump with power connected, leave the water tap open during an active overflow, or run repeated cycles with standing water
  • Do not run an extra test cycle after the source tells you to stop or arrange service for F10

Preventive maintenance

  • 1
    Keep user-accessible filters, seals, hoses, and drain connections clean and inspect them periodically for damage or seepage
  • 2
    Keep the filters and pump area clean and do not run the dishwasher with visible water around its base
  • 3
    If F10 begins recurring despite the documented maintenance, stop repeating the same action and request exact-model diagnosis

Frequently asked questions

What exactly does F10 identify?

Gorenje identifies it as The dishwasher has detected too much water.

Which action is actually supported for F10?

Gorenje's F10 procedure is limited to unblocking the accessible drainage-pump area; Do not infer an inlet valve or pump replacement from F10; use service when overfilling continues.

Can I run another test after F10?

Not unless the official procedure above explicitly includes it. Complete the safe external actions, then keep the appliance stopped at the service boundary.

Does F10 prove which part failed?

No. It identifies “The dishwasher has detected too much water”; parts are selected only after the exact model and failed function are confirmed.

What information should accompany a service request?

The F10 photo, full model and serial number, the operating stage when it appeared, and the result of each published check.

Related faults

Compare related codes for the same appliance or manufacturer before replacing parts.